Siemens SINAMICS S Manuel page 979

Parameter
Meaning
Symbol
Parameter name [Units] Monitoring parameter
rxxxx [x..y] (parameter may appear
multiple times).
Parameter name [Units]
Monitoring parameter
Index name with index
rxxxx[x] (parameter may appear
multiple times).
[aaaa.b]
Parameter name Setting parameter
(if the parameter appears
from ... to [Units]
a multiple number of times,
pxxxx[y...z] (Def)
then diagram references
are specified).
[aaaa.b]
Parameter name
Index name
Setting parameter with
from ... to [Units]
index (if the parameter
pxxxx[y] (Def)
appears a multiple number
of times, then diagram
references are specified).
Data sets
Symbol Meaning
pxxxx[C]
Parameter belongs to the
Command Data Set (CDS).
pxxxx[D]
Parameter belongs to the
Drive Data Set (DDS).
pxxxx[E]
Parameter belongs to the
Encoder Data Set (EDS).
pxxxx[M]
Parameter belongs to the
Motor Data Set (MDS).
pxxxx[P]
Parameter belongs to the
Power unit Data Set (PDS).
1 2
DO: All objects
General - explanation of the symbols (part 1)
Connectors
Symbol
Meaning
Parameter name
Connector input CI with index
pxxxx[y...z]
range [y...z]
(xxxx [y])
Parameter name
Index name
Connector input CI with index [y]
pxxxx[y]
(xxxx[x])
Parameter name [Units] Connector output CO with
[dimension units] and index range
rxxxx[y...z]
[y...z]
(the parameter may appear
multiple times).
Connector output CO
Parameter name [Units]
[dimension units] and with index [y]
Index name
(the parameter may appear
rxxxx[y]
multiple times).
Information on parameters, binectors, connectors
Symbol Meaning
Parameter name (max. 18 characters)
Parameter name
[dimension units]
[Units]
rxxxx[y] or "r" = monitoring parameter. These parameters are read-only
"xxxx" stands for a four-digit parameter number
rxxxx[y...z]
"[y]" specifies the valid index, "[y...z]" specifies the applicable index range
rxxxx.ww[y]
rxxxx.ww ".ww" specifies the bit number (e.g. 0...15).
"p" = setting parameter. These parameters can be changed.
pxxxx[y] or
"xxxx" stands for a four-digit parameter number,
pxxxx[y...z]
"[y]" specifies the applicable index, "[y...z]" specifies the applicable index range
pxxxx.ww[y]
".ww" specifies the bit number (e.g. 0...15).
pxxxx.ww
Value range
from ... to
Parameter number (xxxx) and Index number [y].
(xxxx[y])
(Def) Factory setting.
Factory setting with bit number as prefix.
(Def.w)
Diagram references for setting parameters that occur a multiple number of times.
[aaaa.b]
[Function diagram number, signal path]
3 4
Connectors/binectors
Binectors
Symbol Meaning Symbol
Parameter name
Parameter name
Binector input BI with rxxxx
index range [y...z] and rxxxx
pxxxx[y...z]
factory setting (Def.x) with
(Def.x)
Cross references between diagrams
bit x.
Symbol
Parameter name
Binector input BI with
Bit name
Signal path
index [y] and factory
pxxxx[y]
setting (Def.x) with bit x.
(Def.x)
Parameter name
Binector output BO
(the parameter may
rxxxx
[cccc.d]
appear multiple times).
To "function diagram name" [aaaa.b] = for binectors.
Important: No cross-reference to the main diagrams or that go to or
Parameter name
Binector output BO with
Bit name
bit yy
Cross references for control bits
rxxxx.yy
(the parameter may
appear multiple times).
Symbol
pxxxx
[aaaa.b]
Sampling times
Symbol
pxxxx[Y] (ZZZ.ZZ µs)
p0115[y] (Drive Object)
p0115[y] (Motor Modules)
PROFIBUS sampling time
CAN bus sampling time
5 6
fp_1020_01_eng.vsd
20.09.05 V02.04.00
Meaning
Connector/binector output CO/BO
Meaning
The function diagrams are sub-divided into signal
paths 1...8 for faster orientation.
Text Text = Unique signal designation
[aaaa.b]
aaaa = Signal goes to the target diagram aaa
b = Signal goes to signal path b
Text = Unique signal designation
Text
cccc = Comes from source diagram cccc
d = Signal comes from signal path d
from overview diagrams.
Meaning
pxxxx= Original parameter of signal
aaaa = Signal comes from the source diagram aaaa
b = Signal comes from signal path b
Meaning
Setting parameter with factory setting to
select the time slice.
Time slice depending on the pre-setting
p0112 of the drive object.
Time slide depending on the rated pulse
frequency of the motor module.
a) If clock-cycle synchronous, then bus
cycle time alias DP cycle (Tdp).
b) Otherwise 4000.00 µs.
Time slice 4000.00 µs.
Background There is no fixed sampling time for this
function. The processing is made in the
Refer to [1020.7]
background. The cycle time depends on
the computational load of the control unit.
A static state is displayed here. The
Not relevant
sampling time data is not relevant.
Refer to [1020.7]
7
Function diagram
SINAMICS S
8
- 1020 -