battioni Pagani WPT Série Notice D'emploi Et D'entretien page 76

Instruction Manual
for WPT, KTS, KPS, KTM, WSM series use and maintenance
8) fix the hydraulic motor transmission coupling to the anterior pin by the
screw located inside the pin;
Fix hydraulic motor support to the coupling flange;
9)
Mount the hydraulic motor on its support with screws;
10)
KPS SERIES
.../M - MA .../G - GA
.../K - KA
1) Disassemble the Seeger ring.
2) Disassemble the bearing
3) Replace flange gasket;
4) Insert the cotter pins included
in the body
5) Fasten the multiplier box to
the body by means of screws
tightened at 45 ÷ 55 Nm
6) Assemble the bearing on the
moltiplier box by using a
buffer and insert the com-
pensating ring and insert the
Seeger ring;
7) Insert the spacer and assemble
the pinion on the shaft
8) Assemble the fastening locknut
of the pinion;
9) Insert the gear in the bearing
housing
10) Assemble the box cover;
11) Fill the multiplier box with oil
up to the level.
12) Remove the centring pins
from the body.
WPT SERIES
1) Replace the front flange gasket;
.../M - MA
2) fix the gearbox to the coupling flange with
screws;
3) fit pinion to the rotor pin;
4) fit the self-locking nut for fixing the pinion;
5) insert the gear in the bearing seat;
6) replace the gearbox cover gasket;
7) fix the gearbox cover;
pag. 50
.../P
1) Disassemble the Seeger ring.
2) Disassemble the bearing
3) Replace flange gasket;
5) Fasten the multiplier box to
the body by means of screws
tightened at 45 ÷ 55 Nm
5) Fasten the flange to the body
by means of screws tightened
at 45 ÷ 55 Nm
6) Assemble the bearing on the
flange by using a buffer and
insert the compensating ring
and insert the Seeger ring;
7) Reassemble the front
cover on the flange.
8) Remove the centring pins from
the body
2) bring the front flange up to the pump body,
positioning it in alignment with the clamping
holes;
tighten the clamping screws of the front
3)
flange to the body;
attach the front cover to the flange with
4)
clamping screws;
connect the lubrication tube by screwing it
5)
to the connecting piece placed on the front
cover;
6) insert the pulleys on the front pin, fixing them
with the key;
8) assemble the locknut to fasten the pinion;
9) put the gear into the bearing housing;
10) replace box cover gasket;
11)assemble multiplier box cover;
.../D
1) Disassemble the Seeger ring.
2) Disassemble the bearing
3) Replace flange gasket;
4) Insert the cotter pins included
in the body
5) Fasten the flange to the body
by means of screws tightened
at 45 ÷ 55 Nm
6) Assemble the bearing on the
flange by using a buffer and
insert the compensating ring
and insert the Seeger ring;
7) Reassemble the front cover on
the flange.
8) Reassemble the shrunk-on
9) Remove the centring pins from
the body.
.../P
2 ) bring the front flange up to the pump body, posi-
3) tighten the clamping screws of the front flange
4) attach the front cover to the flange with clamp-
5) connect the lubrication tube by screwing it to the
.../H
1) Disassemble the Seeger ring.
2) Disassemble the bearing
3) Replace flange gasket;
4) Insert the cotter pins included in
the body
5) Fasten the flange to the body by
means of screws tightened at
45 ÷ 55 Nm
6) Assemble the bearing on the
flange by using a buffer and
insert the compensating ring
and insert the Seeger ring;
7) Reassemble the hydraulic motor
support.
8) Remove the centring pins from
the body.
.../D
tioning it in alignment with the clamping holes;
to the body;
ing screws;
connecting piece placed on the front cover;