Re-Fitting - Re-Installation; Front Part Re-Fitting - battioni Pagani WPT Série Notice D'emploi Et D'entretien

4) remove the lubrication tube by unscrewing it
from the connecting piece placed on the con-
necting flange of the hydraulic motor support;
5) remove the connecting flange of the hydraulic mo-
tor support by unscrewing the clamping screws;
6) remove the front flange by unscrewing the
screws that fix it to the body;
8) KTM, KTS, WSM SERIES: unscrew the six clamping screws of the back pin of the rotor;
9) KTM, KTS, WSM SERIES: use two screws for screwing into the threaded extraction holes until the cover is removed;
3.9 - RE-FITTING – RE-INSTALLATION
IMPORTANT: Before proceeding with any re-fitting, replace the gaskets of the opened parts.

3.9.1 - FRONT PART RE-FITTING

KTM, KTS, WSM SERIES
1) Insert the front pin in its seat in the rotor, being careful to avoid putting the front pin in the place of the back one and fix it with screws;
2) Replace the front flange gasket;
.../M - MA
3) bring the gearbox coupling flange up to the
pump body, positioning it with the dowel
pins supplied, in alignment with the clamping
holes;
4) tighten the clamping screws of the gearbox
coupling flange to the body with a torque set-
ting of 80 Nm;
5) remove the dowel pins;
6) fix the gearbox to the coupling flange with
screws;
7) fit pinion to the rotor pin;
8) fit the self-locking nut for fixing the pinion;
9) insert the gear in the bearing seat;
10) replace the gearbox cover gasket;
11) fix the gearbox cover;
bring the front flange up to the pump body, positioning it with the dowel
3)
pins supplied, in alignment with the clamping holes;
tighten the clamping screws of the front flange to the body with a torque
4)
setting of 80 Nm;
remove the dowel pins;
5)
fix the connecting flange of the hydraulic motor support to the front
6)
flange with screws;
connect the lubrication tube by screwing it to the connecting piece placed
7)
on the hydraulic motor support coupling flange;
for WPT, KTS, KPS, KTM, WSM series use and maintenance
4) use two screws to screw into the threaded
extraction holes until the cover is removed;
5) remove the multiplier box;
6) KTS SERIES: unscrew the fixing screws of
the pump body of the multiplier coupling flange
and remove it;
3) bring the front flange up to the pump body,
positioning it with the dowel pins supplied, in
alignment with the clamping holes;
4) tighten the clamping screws of the
front flange to the body with a torque
setting of 80 Nm;
5) remove the dowel pins;
6) attach the front cover to the flange
with clamping screws;
7) connect the lubrication tube by screw-
ing it to the connecting piece placed
on the front cover;
8) Insert the pulleys on the front pin, fixing it
with the key;
.../H
4) use two screws to screw into the threaded
extraction holes until the cover is removed;
5) remove the multiplier box;
6) KTS SERIES: unscrew the fixing screws of
the pump body of the multiplier coupling flange
and remove it;
.../P
3) bring the front flange up to the pump body,
4) tighten the clamping screws of the front
5) remove the dowel pins;
6) attach the front cover to the flange with
7) connect the lubrication tube by screwing it
8) Insert the conducting pulley (if present) on the
9) Fix the transmission sleeve with the ring by
10) Fix the splined hub by tightening the relevant
11) Insert the guard and tighten the screws (if
3) move the multiplier coupling flange close to the pump body, posi-
tioning it, using dowel pins supplied, at the fixing holes;
4) tighten the fixing screws of the multiplier coupling flange to the in
body with tightening torque equal to
5) remove the centering pins;
6) fix the multiplier box to the coupling flange with
7) assemble the pinion of the rotor pin;
Instruction Manual
.../D
positioning it with the dowel pins supplied, in
alignment with the clamping holes;
flange to the body with a torque setting of 80
Nm;
clamping screws;
to the connecting piece placed on the front
cover;
front pin, fixing it with the key;
tightening the top screw;
screws;
present);
.../G - GA
80 Nm;
screws;
pag. 49