Publicité
17. Déclaration d'incorporation (originale)
EU Declaration of Incorporation (DOI)
Manufacturer:
Universal Robots A/S
Energivej 51
DK-5260 Odense S Denmark
Description and Identification of the Partly-Completed Machine(s):
Product and
Function:
Model:
Serial Number: Starting
Incorporation:
It is declared that the above products fulfil, for what is supplied, the following directives as detailed below:
When this partly completed machine is integrated and becomes a complete machine, the integrator is responsible for the
completed machine fulfiling all applicable Directives, applying the CE mark and providing the Declaration of Conformity (DOC).
I. Machinery Directive 2006/42/EC
II. Low-voltage Directive 2014/35/EU
III. EMC Directive 2014/30/EU
Reference to the harmonized standards used, as referred to in Article 7(2) of the MD & LV Directives and Article
6 of the EMC Directive:
(I) EN ISO 10218-1:2011
(I) EN ISO 12100:2010
(I) EN ISO 13849-1:2023
(I) EN ISO 13849-2:2012
(I) EN ISO 13732-1:2008
Reference to other technical standards and technical specifications used:
(I) ISO 9409-1:2004
(I)
ISO/TS 15066:2016 as applicable
(III) EN 60068-2-1:2007
(III) EN 60068-2-2:2007
The manufacturer, or his authorised representative, shall transmit relevant information about the partly completed
machinery in response to a reasoned request by the national authorities.
Approval of full quality assurance system by the notified body Bureau Veritas: ISO 9001 certificate #DK015892
and ISO 45001 certificate #DK015891.
Odense Denmark, 31 March 2025
Universal Robots A/S, Energivej 51, DK-5260 Odense S, Denmark
CVR-nr. 29 13 80 60
Manuel utilisateur
(in accordance with 2006/42/EC Annex II B)
Person in the Community Authorized to Compile the Technical File:
David Brandt
Technology Officer, R&D
Universal Robots A/S, Energivej 51, DK-5260 Odense S
Industrial robot multi-purpose multi-axis manipulator with control box & with or without a 3PE teach
pendant. Function is determined by the completed machine (robot application or cell with end-
effector, intended use and application program).
UR15: Below cited standards and this declaration include:
2025
6
8
00002 and higher
year
Sequential numbering, restarting at 0 each year
series
7 = UR15
Universal Robots UR15 shall only be put into service upon being integrated into a final complete
machine (robot application or robot cell), which conforms with the provisions of the Machinery
Directive and other applicable Directives.
The following essential requirements have been fulfilled:
1.1.6, 1.2.1, 1.2.4.3, 1.2.5, 1.2.6, 1.3.1, 1.3.2, 1.3.4, 1.3.8.1, 1.3.9, 1.4.1 with 3PE TP,
1.5.1, 1.5.2, 1.5.4, 1.5.5, 1.5.6, 1.5.10, 1.6.3, 1.7.1.1, 1.7.2, 1.7.4, 1.7.4.1, 1.7.4.2,
2.2.1.1, 4.1.2.1, 4.1.2.3, 4.1.2.4 (sling), 4.1.3, 4.3.3, Annex VI.
It is declared that the relevant technical documentation has been compiled
in accordance with Part B of Annex VII of the Machinery Directive.
Reference the LVD and the harmonized standards used below.
Reference the EMC Directive and the harmonized standards used below.
(I) EN ISO 13850:2015
(I) EN 60204-1:2018
(II)
EN 60529:1991+A1:2000+A2:2013
(I) EN 60947-5-5:1997+A1:2005
+A11:2013+A2:2017
(I) EN 60947-5-8:2020
(III) EN 60068-2-27:2008
(III) EN 60068-2-64:2008+A1:2019
(II) EN 60320-1:2021
(II) EN 60664-1:2007
(III) EN 61000-3-2:2019
(III) EN 61000-3-3:2013
(III) EN 61000-6-2:2019
(III) EN 61000-6-4:2019
(II) EN 61140:2002/ A1:2006
(II) EN 61784-3:2010 [SIL2]
(III) EN 61326-3-1 2017
Roberta Nelson Shea,
Global Technical Compliance Officer
Phone +45 8993 8989
Fax +45 3879 8989
246
original: EN
NOTE:
This DOI is
NOT applicable when the
OEM Controller is used.
See control box markings.
1.1.2, 1.1.3, 1.1.5,
[Industrial locations SIL 2]
info@universal-robots.com
www.universal-robots.com
UR15
Publicité
