First Green Industries MiniZ400 Instructions D'utilisation Et D'entretien page 11

Changes to the loader may only be made with the manufacturer's prior written consent. If necessary, the consent of the
competent authority must be obtained.
Changes to the brake system, steering, controls, peripheral vision and special equipment (such as attachments) are also
subject to the manufacturer's prior written consent.
!
Caution
When welding on the loader, the batteries and all connections to the electrical control units must
be disconnected. More detailed information on these topics can be obtained from an authorized
service centre.
Caution
!
Additional openings in the battery cover present a risk of explosion! Volatile gases may be
released, which can explode and cause harm, including fatal injuries. Sealing the openings with
plugs does not provide an additional barrier to gas leakage.
Do not drill any holes into the battery cover!
Otherwise the structural stability of the battery cover will be compromised, and it may then break. It can hit the driver's
position, which poses a risk of accident as a result of the uncontrolled movement of the controls while driving.
Should the manufacturer be wound up and its company is not taken over by a new owner (legal entity), the operator can
make modifications to the loader.
In doing so, however, the operator must observe the following rules:
$ production documents, test reports and assembly instructions related to the modification must be retained and
be available at all times;
$ check that the modifications have not affected the validity of the rating plate, information labels, warning labels or
the operating manual and, if necessary, correct these;
$ modifications can only be designed, approved and implemented by a design office that specializes in designing loaders
in accordance with the standards and directives in force at the time of the modifications.
! Caution
Never allow a ride with a passenger. Never use the work tool as a platform for another person.
A failure to observe the vehicle-related instructions or warnings may result in injury or death.
!
Caution
Hot liquid can cause severe burns. Protect yourself with suitable protective clothing.
20
!
Caution
Improper clamping of the work tool may cause injury or death. Do not start working with the
machine until you have made sure that the mechanism pins are fully inserted. Follow the work
procedures specified in the operating and maintenance manual.
Caution
!
This machine is equipped with a communication device. Where electric detonators are used, this
communication device should be switched off at a distance of 12 m (40') from the blasting point
for satellite systems, and at a distance of 3 m (10') from the blasting point for mobile systems,
or at a distance that complies with the applicable legal requirements. A failure to observe this
provision may result in interference with explosive blasting operations, which can result in serious
injury or death.
6.3.3 CHANGES TO THE DRIVER'S PROTECTIVE ROOF AND ROOF LOAD
!
Caution
This machine is not equipped with a FOPS or ROPS protective structure.
Dropping a load or the loader overturning with the vehicle operator's (driver's) position impacted
as a result can be fatal. Potential danger to life!
6.3.4 USE OF NON-ORIGINAL PARTS
Original parts, attachments and accessories are specially designed for this loader. We would like to draw your attention
specifically to the fact that non-original parts, attachments and accessories from other suppliers have not been tested and
approved by First Green.
Before installing such components, we recommend obtaining the consent of the manufacturer and, if applicable, of the
competent inspection authorities.
The manufacturer accepts no liability for damage caused by using non-original parts and accessories that have not been
approved.
!
Caution
The installation and use of such products may have a negative effect on the design characteristics
of the loader and thus also compromise passive driving safety.
6.3.5 LOADER DEFECTS AND DAMAGE, INCORRECT USE OF SAFETY DEVICES
Damage and other faults of the loader or its attachment must be reported to the operator immediately so that the fault can
be rectified by the same.
Loaders and attachments that are not safe or functional must not be used until properly repaired.
Do not remove, disable or turn off safety devices or switches!
Predefined settings may only be changed with the manufacturer's consent.
Works on the electronic system (such as connecting radio, additional headlights etc.) are only permitted with the
manufacturer's written consent. All interventions in the electrical system must be properly documented!
6.3.6 RISK TO STABILITY
To ensure stability, the following rules must be observed:
$ only use tracks with the same allowable level of wear;
$ only use tracks approved by the manufacturer;
$ only use high-quality products.
Tracks approved by the manufacturer can be found in the spare parts list. If you want to use other tracks, you must first
obtain the manufacturer's consent!
When replacing tracks, always make sure that the loader is never tilted to one side. More detailed information on these
topics can be obtained from an authorized service centre.
!
Caution
A failure to follow these instructions and information may result in compromised stability. The
loader may overturn; there is a risk of an accident.
6.3.7 MEDICAL DEVICES
Only use devices that are sufficiently protected against electromagnetic interference. Medical devices such as pacemakers
or hearing aids may not function properly during the operation of the loader.
Check with your doctor or the manufacturer of your medical device to make sure that it is sufficiently protected against
electromagnetic interference.
!
Caution
Electromagnetic interference with medical devices may occur.
6.4 INSULATION TEST
The insulation of the loader must provide sufficient insulation resistance. Consequently, as part of the tests under the FEM
standard, the insulation resistance must be checked at least once a year in accordance with ČSN EN 1175, DIN 43539, VDE
0117 and VDE 0510. The results of the insulation tests must meet at least the test values given in the two tables below.
Contact an authorized service centre if you want to carry out insulation tests!
!
Caution
The electrical system of the loader and the traction battery must be checked separately!
Test values for the traction battery and the complete loader:
RECOMMENDED TEST
COMPONENT MEASUREMENT RATED VOLTAGE U TEST VALUES
VOLTAGE
BAT
50 V DC 24 V > 1200
Battery
Battery 100 V DC Batt. + Batt. - compart- 48 V > 2 400
ment
100 V DC 48 V > 2 400
TEST
VALUES
RATED VOLTAGE TEST VOLTAGE MINIMUM VALUES DURING SERVICE LIFE
FOR NEW
LOADERS
24 V 50 V DC At least 50 k > 24 k
48 V 100 V DC At least 100 k > 48 k
80 V 100 V DC At least 200 k > 80 k
6.5 SAFETY INSTRUCTIONS FOR HANDLING CONSUMABLES
6.5.1 ALLOWABLE CONSUMABLES
Non-compliance with the safety regulations applicable to consumables may result in injury, death or damage to the
environment.
Observe the safety regulations when handling such materials.
Allowable materials necessary for operation are listed in the maintenance data table.
6.5.2 OILS
!
Caution
Oils are flammable!
21