Homelite CSP-3314 Manuel D'utilisation page 32

Homelite all in one.qxp
GB
F D E I
OPERATION
1 Litre + 20 ml
2 Litres + 40 ml
3 Litres + 60 ml
4 Litres + 80 ml
5 Litres + 100 ml
CHAIN OIL SYSTEM (Fig. 7)
Use HOMELITE Bar and Chain Oil. It is designed for chains
and chain oilers, and is formulated to perform over a wide
temperature range with no dilution required. Chainsaw
should use approximately one tank of oil per tank of fuel.
NOTE: Do not use dirty, used or otherwise contaminated
oils. Damage may occur to the oil pump, bar, or chain.
1. Carefully pour the bar and chain oil into the tank.
2. Fill the oil tank every time you fuel the engine.
STARTING THE ENGINE (Fig. 8)
WARNING
Keep your body to the left of the chain line.
Never straddle the saw or chain, or lean over
past the chain line.
1. Place the chainsaw on level ground and ensure that no
objects or obstructions which could come in contact
with the bar and chain are in the immediate vicinity.
2. Hold the front handle firmly with the left hand and put
your right foot onto the base of the rear handle.
STARTING A COLD ENGINE (Fig. 3 & 8 - 14)
3. Move the chain brake to the BRAKE position (B).
NOTE: Set the chain brake by pushing the chain brake
lever/hand guard forward (towards the bar), to the
brake position. Refer to "Operation – Operating the
Chain Brake" later in this manual for additional
information.
4. Set the ignition switch to the RUN (I) position (A).
5. Fully press and release the PRIMER BULB (C) 7 times.
6. Pull CHOKE (D) lever all the way OUT to full position (E).
The partial throttle position is automatically set when the
choke lever is set at fill choke.
NOTE: For 33 cc, engage trigger release (F). While
squeezing both trigger release and throttle trigger (G),
push in the throttle lock button (H). Release the throttle
trigger. This latches the trigger for starting (Fig. 12a).
23/12/05 16:14
P NL S DK N FIN GR HU
English
=
}
=
= 50:1
=
=
Page 24
CZ RU RO PL SLO HR TR EST LT
7. Pull STARTER (F) until engine attempts to start.
Slowly pull the starter grip out for a short distance until
you feel the starter engage, then briskly pull straight
up. Do not pull to the end of the rope; this may
damage the starter. Hold onto the grip during
rewinding. Pull the starter rope until the first firing of
the engine is heard (no more than five pulls).
NOTE: A new unit may require additional pulls.
8. Push choke lever (D) all the way IN (G).
9. Pull starter until engine runs.
NOTE: Allow the saw to run in this position
15-30 seconds depending upon the temperature.
10. SQUEEZE and release the throttle trigger (H). Depress
the throttle trigger which releases the trigger lock
button. Squeeze and release the throttle trigger to let
the engine idle.
CAUTION
Failure to release partial throttle when chain
brake lever is in the brake position will result in
serious damage to the unit. Never squeeze and
hold the throttle trigger while the chain brake is in
the brake position.
Now you are ready to pick up the saw. Use the proper grip
for both handles. Refer to "Operation-Proper Grip on
Handles" later in this manual for additional information.
STARTING A WARM ENGINE
Follow the instructions for starting a cold engine (steps 1-9),
but do not attempt to start in the full choke position
(skip step 6). Push and release primer bulb 7 times. Pull the
choke out and push back it in to the original run position.
STOPPING THE ENGINE (Fig. 15)
Release the throttle trigger and let the engine return
to idle.To stop the engine, move the ignition switch to the
"O" stop position (J). Do not put the chainsaw on the
ground when the chain is still moving. For additional
safety, set the chain brake when the saw is not in use.
In the event that the ignition switch will not stop the saw,
pull the choke lever out to the fully extended position
(Full Choke) and engage chain brake to stop the engine.
If the ignition switch will not stop the saw when set to the
"O" stop position, have the ignition switch repaired before
using the chainsaw again to prevent unsafe conditions or
serious injury.
IMPORTANT: When you have finished using the saw,
relieve tank pressures by loosening the CHAIN OIL and
FUEL MIX caps. Then retighten the caps. Allow the
engine to cool before storing.
24
LV SK BG