Publicité
Dis T.1634007e
With
and
you scroll through the items and then by pressing
only the value is selected, showing that it is possible to change it.
ENTER
With
and
you change the values. By pressing
is accepted. Pressing
row is selected, indicating that it is only possible to scroll through the
items.
DESCRIPTION OF ITEMS RELATED TO THE REMOTE UNITS:
indicates the number of the R.U. installed. This number corresponds to the R.U. that
REM.UNIT
must be set with the DIP-Switches (please see the specific RU manual).
Sets the number of serial port which the R.U. is connected to. The control unit
manages two RS485 serial ports, COM 1 and COM 2.
PORT
Please enter the correct port number. Note that if the number of R.U. or the port is not
correct, the R.U. will result out of line.
The Control Unit considers configurable, the numbers of the sensors according to the number
of R.U. configured. The 1
from 17 to 24. The same concerns the relay outputs (if any), the 1
from no.10 to 17, the 2
REMOTE UNITS - DELETE (Level 2)
This item allows you to delete a R.U. or a group of R.U. Press
level and the procedure is the same as described in the previous paragraph COPY.
After choosing the Remote Unit (s) and confirming with
will warn you that the operation was successful.
Then the screen returns to the beginning of the CANCEL management.
WARNING: deleting a Remote Unit, will be deleted both all the sensors connected to it, both
the corresponding relay outputs, if installed (R.U. no.1 OUT 10 to 18 and for the R.U. n.2 OUT
19 to 25). IMPORTANT: If these relays were related to Sensors or Areas that do not belong to
the R.U. cancelled, those outputs in the configuration will be set to 0 (no relay), then the
outputs of these sensors will have to be reconfigured.
REMOTE UNITS - MODIFY (Level 2)
To modify a R.U. already configured, press
to modify, then scroll through the parameters and choose the one you want to modify, with the same
procedure described in the
REMOTE UNITS - DETAILS
This item allows you to see parameters of a R.U. already configured, pressing
The voices are the same as the R.U. configuration. You can scroll
through them using
the end of the screen: Present or Out of Line or Disabled.
In case you want to go back, press
SENSORS
In this submenu you can manage the sensors connected to the unit.
The 3-CONFIGURE menu, should only be used for a new sensor,
to modify the parameters of an already configured sensor only
use the 6-MODIFY menu.
Below, the individual items are described in detail, with the corresponding level password, which is
indicated in brackets.
TECNOCONTROL S.r.l. - Via Miglioli, 47 20054 SEGRATE (MI) - Tel. 02. 26 92 28 90 - Fax 02. 21 33 734
CE424P User manual
restores the previous value and the entire
ESC
st
R.U. manages the sensors from no.9 to 16, the 2
nd
R.U. those from no.18 to 25.
REMOTE UNIT - CONFIGURE
and
. The status of the R.U. is indicated at
.
ESC
the change
ENTER
on the relevant item. The access
the window,
on the relevant item. Choose the number of the U.R.
paragraph
Pag. 21/52
CONFIG. REM. UNIT
REM. UNIT N.
1
LINE
COM 1
SAVE
nd
R.U. those
st
R.U. controls the relays
REMOT UNIT
N. 1
DELETED
on its item.
REM. UNIT DETAILS
REM. UNIT.
N. 1
PORT
N. 1
STATUS:
PRESENT
SENSORS
1-ENABLE
2 DISABLE
3 CONFIGURE
4 COPY
5 DELETE
6 MODIFY
7 DETAILS
Publicité
