Filling The Tank; Starting The Engine - Efco GST 360 Manuel D'utilisation Et D'entretien

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 43

FILLING THE TANK

Stir the mixture well before refuelling.
WARNING: Follow safety instruction for
fuel handling. Always shut off engine
before fuelling. Never add fuel to a machine
with a running or hot engine. Move at least 3
m from refuelling site before starting engine.
DO NOT SMOKE!
1. Clean surface around fuel cap to prevent
contamination.
2. Loosen fuel cap slowly.
3. Carefully pour fuel mixture into the tank.
Avoid spillage.
4. Prior to replacing the fuel cap, clean and
inspect the gasket.
5. Immediately replace fuel cap and hand
tighten. Wipe up any fuel spillage.
WARNING: Check for fuel leaks, if any
are found, correct before use. Contact a
Servicing Dealer if necessary.
OIL FILLING AND CHAIN LUBRICATION
The saw chain is automatically lubricated during
use by a pump which normally requires no
maintenance. The oil flow is pre-regulated by the
manufacturer to ensure a sufficient oil delivery
even under heavy working conditions. During
cutting of thin timber a possible oil dripping is
normal.
- Always wipe off around the filler hole before
unscrewing the cap (13, Fig. 2) so that no dirt
enters the oil reservoir.
- During work watch the oil level.
- After the filling, operate the motor 2 or 3 times
to restore correct oil delivery.
- In case of faults do not try to repair the
machine yourself, but apply to your authorized
dealer.
Correct chain lubrication during the cutting
phase reduces wear to a minimum between the
chain and bar thus prolonging life. Always use a
good quality oil.
WARNING - Never use waste oil.
Always use biodegradable lubrificant
(eco-lube Oleo-Mac/Efco) which is specific
for bar and chain and also respectful towards
nature, operator health and chain saw's parts.
Before starting make sure the chain is not
obstructed.
When the chainsaw is running, grip the
front handle firmly with your left hand
and the back handle with your right hand
(Fig. 11).
- Do not lean forward and do not cut above
shoulder height; gripping the chain saw at the
top of the handle makes it difficult to control
and counteract kickback.
- Check that all parts of the body are kept
away from the chain and muffler.
- L e f t - h a n d e r s s h o u l d f o l l o w t h e s e
instructions too. Keep a proper cutting
stance.
Over exposure to vibrations can result in
blood-vessel or nerve injury to persons
suffering with blood circulation problems.
Seek medical attention if you experience
physical symptoms such numbness, lack of
feeling, reduction in normal strength, changes
in the colour of the skin. These symptoms
normally appear in the fingers, hands or
wrists.
Engine is Flooded
- Pry off the spark plug boot.
- Unscrew and dry off the spark plug.
- Open the throttle wide.
- Pull the starter rope several times to clear the
combustion chamber.
- Refit the spark plug and connect the spark
plug boot, press it down firmly.
- Set the choke lever to OPEN position – even if
engine is cold.
- Now start the engine.
WARNING – Never start the saw engine
without the bar, chain and clutch cover
(chain brake) assembled - or else the clutch can
come loose and cause personal injuries.

STARTING THE ENGINE

The chain brake must be engaged when
starting the saw. Set the chain brake by
pushing the chain brake lever / hand guard
forward (towards the bar), to the brake
position (Fig. 12). Fill the carburetor by pushing
primer bulb (14, Fig. 2). Put the choke lever
(D, Fig. 13) in the CLOSE position. Place the
chainsaw on the ground in a stable position.
Check that the chain is free to turn and will not
come into contact with any foreign objects.
Before you start the engine, make sure the saw
chain is not contacting any object. Never try
I
GB
F
D
E
NL
P
GR
TR
CZ
SK
RUS
UK
PL
H
LV
EST
LT
RO
27

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mtt 3600

Table des Matières