Wall Installation - Side Hung Bracket Or Side/End Hung Bracket - Invacare EC-Track Robin Manuel De Maintenance

•
150 mm for rail profile L
When using wall support legs, cut the support leg profile to an
appropriate length at the floor end.
Remember to make allowance for the floor support foot.
In case of skirting boards, either use the high wall support foot, or cut
away the skirting board.
Always install wall support legs right at the wall in their full length.
Mark for holes using a level, and drill the holes.
Concrete wall
When mounting a freely hanging rail into a concrete wall, a wall
bracket should be used for mounting.
For mounting, we recommend using either expansion bolts M10x68
(e.g. Hilti HSA or equal), drilling depth min. 60 mm, Ø10, or adhesive
mortar (e.g. Hilti HIT-HY 150 and HAS M10 or equal), drilling depth
min. 95 mm, Ø12 (when mounted in wet rooms, use stainless steel
HAS quality A4-70).
Brick wall
When mounting into bricks, ordinary wall brackets should be used.
However, we recommend using floor supports if the brick wall is
very porous.
For mounting into massive bricks, we recommend using adhesive
mortar (e.g. Hilti HIT-HY 50 and HAS M10 or equal), drilling depth
min. 90 mm in ½ brick and 170 mm in 1/1 brick, Ø12., (when
mounted in wet rooms, use stainless steel HAS quality A4-70).
For mounting in hollow bricks, we recommend using either a frame
sheer connector (e.g. Hilti HRDUGT or equal), drilling depth min. 80
mm, Ø10, or adhesive mortar (e.g. Hilti HIT-HY 20, and HAS M10
or equal), drilling depth min. 95 mm, Ø16.
For mounting into porous brickwork, we recommend using adhesive
mortar (e.g. Hilti HIT-HY 50 and HAS M10 or equal), drilling depth
min. 90 mm in ½ brick and 170 mm in 1/1 brick, Ø12. If wall supports
are used when mounting, use HAS M8, drilling depth min. 80 mm,
Ø10.
Lightweight concrete
When mounting in light concrete, you may either use wall brackets or
wall supports, depending on the condition of the wall. For mounting,
we recommend using adhesive mortar (e.g. Hilti HIT-HY 50 and HAS
M10 or equal), drilling depth min. 90 mm, Ø12 (M8 for mounting of
wall supports).
You may also use a light concrete sheer connector (e.g. Hilti HGN,
HUD-1 10L or equal), drilling depth min. 90 mm, Ø10 / HUD-1 8L,
drilling depth min. 80 mm, Ø8.
1586749-B
Gypsum wall
Refer also to chapter 3.7 Wall support legs, page 19.
1. Complete the installation of the wall bracket or the wall support
leg with console, wall support foot and plugs for covering the
screw holes.
2. Insert the hoist trolley or the traverse trolley in the rail. The
hoist trolley can be oriented in both directions, whereas the
orientation of the traverse trolley must correspond to the layout
of the traverse system.
3. Insert end stops at both ends of the rail and finger-tighten them
at first.
4. Insert the insertion tube in the rail. The hole in the tube must
face outwards.
5. Lift the rail while holding on to the insertion tube to prevent it
from sliding into the rail.
6. Mount the insertion tube on the console at the wall bracket or
the wall support leg.
7. Adjust the rail lengthwise to achieve the correct distance
between the wall and the rail.
8. There must be an overlap of at least 300 mm between the rail
and the insertion tube. Check to verify by looking through the
inspection hole on the side of the rail. The inspection hole is
located exactly 300 mm from the end of the rail
9. When the rail is properly positioned, drill a Ø7 mm hole through
the rail and the insertion tube, approx. 100 mm from the end of
the rail. Secure the rail in position with passing bolts M6 with
locking nuts.
10. After positioning the rail, adjust the end stop to its proper
position. When positioning the end stop, make sure that the
hoist will not hit the wall. With a traverse system, ensure that
the two traverse trolleys hit the end stop simultaneously.
Angular, wall-mounted
The rail can be mounted diagonally in the room. The rail must be
angled max. 45°.
The mounting is carried out as described for ordinary wall mounting
with or without wall supports. However, the tube is delivered
prepared for angled mounting.
3.4 Wall installation – side hung bracket or
side/end hung bracket
When installing a rail system side hung, the parallel rails can be
installed close to the wall.
When installing a rail system side hung, the wall must have such
strength, that wall support legs are unnecessary.
When installing S profile, 2000 mm is the maximum distance between
each fixation point, but at least 3 points are necessary.
When installing M profile, 4000 mm is the maximum distance between
each fixation point, but at least 3 points are necessary.
Always measure the distance between both walls accurately, in the
correct height and location of the system. The wall bracket can be
Installation
17