Dürkopp Adler 271-140331 Instructions D'emploi page 145

8. Operating and Setting the Direct-current Positioning Drive
E3760/DA40MS02 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 Operating and Indicator Elements of the DA40MS02
Controls (with Integrated Mini Control Panel) . . . . . . . . . . . . .
8.1.1. Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1.2 Display Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1.3 Displaying and Changing the Number of Bartack Stitches
at the DA40MS02 Controls
8.1.4 Reducing the Maximum Speed in the DA40MS02 controls . . . . . .
8.1.5 Displaying the Current Speed in the DA40MS02 Controls
8.1.6 Activating Sewing Functions . . . . . . . . . . . . . . . . . . . . . . .
8.1.7 Changing Parameters in the Operator Level (A) in the
DA40MS02 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1.8 Changing Parameters in the Mechanic Level (B) in the
DA40MS02 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1.9 Changing Parameters at the Special Level (C) in the
DA40MS02 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1.10 Checking and Setting the Positions at the DA40MS02 Controls . . .
8.1.11 Changing the Direction of Rotation at the DA40MS02 Controls
8.1.12 Setting Machine-specific Parameters at the DA40MS02 Controls . .
8.1.12.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1.12.2 Autoselect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1.12.3 Table of Machine-specific Parameters of the DA40MS02 Controls . .
8.1.13 Master Reset at the DA40MS02 Controls
8.2 Control Panel OC-TOP (Optional Equipment) . . . . . . . . . . . . .
8.2.1 Operating and Indicator Elements in the OC-TOP Control Panel . . .
8.2.2 Displaying and Changing the Number of Bartack Stitches
with the OC-TOP Control Panel . . . . . . . . . . . . . . . . . . . . .
8.2.3 Display of the Current Number of Stitches/Min. in the Display
of the OC-TOP Control Panel . . . . . . . . . . . . . . . . . . . . . .
8.2.4 Changing Parameters at the Operator Level (A) . . . . . . . . . . . .
8.2.5 Parameter List at the Operator Level (A) . . . . . . . . . . . . . . . .
8.2.6 Changing Parameters at the "Mechanic Level" and the
"Special Level" with the OC-TOP Control Panel . . . . . . . . . . . .
8.2.7 Checking and Setting the Positions with the OC-TOP Control Panel .
8.2.8 Changing the Direction of Rotation with the OC-TOP Control Panel .
8.2.9 Setting Machine-specific Parameters with the OC-TOP Control Panel
8.2.9.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.9.2 Autoselect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.9.3 Table of Machine-specific Parameters of the DA40MS Controls . . .
8.2.10 Master Reset with the OC-TOP Control Panel . . . . . . . . . . . . .
8.2.11 Malfunction and Error Messages in the DA40MS Controls and
the OC-TOP Control Panel . . . . . . . . . . . . . . . . . . . . . . . .
8.2.12 Seam Programming with the OC-TOP Control Panel . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
48
49
49
50
51
52
. . . . . . 53
54
55
56
57
57
. . . 58
59
59
59
59
60
GB
61
61
63
63
64
64
65
67
68
69
69
69
69
70
72
72