T Led Curing Light - CASTELLINI SKEMA 6 CART Instructions De Service

5.7.1. T LED curing light

Technical specifi cations.
Supply voltage : 24-36 VDC
Max. power absorbed : 6 VA
Light source : 1 5W LED
Wavelength : 430-490 nm
Acoustic signals : at cycle start, every 5 seconds, and at cycle end
Type of operation : intermittent (runs 2 cycles, rests 60 seconds)
General description of the light
a) Light handpiece
b) Rotary end section
c) Fiber optic
d) Eye protection
e) Power cord
f) Start button
NOTE: the curing light can be used in different confi gurations (wand,
gun or any intermediate position) to aid the user.
NOTE: the curing light is delivered in its original packing which should
be kept for future shipment.
Description of the control pad
[ 1 ] LED 1 ( STANDARD cycle ) :
Emission of 1000 mW/cm
at the time of sale).
[ 2 ] LED 2 ( FAST cycle ) :
Emission of 1600 mW/cm
[ 3 ] LED 3 ( STRONG cycle ) :
Emission of 1800 mW/cm
[ 4 ] LED S :
When LED S is on, you access ramp cycle mode and at the same time
the LEDs B, R and L next to it come on:
[ LED S + LED 1 ] ramp cycle B ( BONDING ) :
Ramp cycle with emission of 500 mW/cm
500 to 1000 mW/cm 2 for 5 seconds and 1000 mW/cm
for a total of 15 seconds.
[ LED S + LED 2 ] ramp cycle R ( RAPID RESTORATION ) :
Ramp cycle with emission of 500 mW/cm
2
500 to 2200 mW/cm for 5 seconds and 2200 mW/cm2 for 5 seconds
for a total of 15 seconds.
[ LED S + LED 3 ] ramp cycle L ( LONG RESTORATION ) :
Ramp cycle with emission of 500 mW/cm
2
500 to 1800 mW/cm for 5 seconds and 1800 mW/cm
for a total of 20 seconds.
[ 5 ] Malfunction signalling LED:
This red LED comes on only if there is a malfunction.
[ 6 ] START button:
Pressing the START button starts the cycle selected at that moment
(the cycle indication LED will come on).
If it is pressed again at any time during the cycle, light beam emission
will immediately be interrupted.
[ 7 ] MODE button:
This button is used to select the cycle to be run. It allows changing
from the cycle you are in at that moment to the immediately following
cycle.
The fi rst three cycles (1, 2 and 3) are at constant power and the LEDs
come on individually.
When LED S is on, you access ramp cycle mode and at the same time
the LEDs B, R and L next to it come on.
Once the LED of the cycle you intend to use has come on, the lamp
is ready for use. Pressing the START button, light beam emission is
activated according to the cycle selected .
NOTE: the cycle can be selected and the button is operative
only when the curing light is not emitting any light. If the button is
accidentally pressed while light is being emitted, nothing will happen.
Operation.
WARNING!
The instrument is supplied non-sterile.
Before use, disinfect the lamp grip. The optical fi bre and the eye pro-
tection can be sterilized in a steam autoclave at 135°C.
• Put the fi ber optic ( c ) in its housing until it clicks.
• Attach the curing light handpiece to the end of its power cord and tighten
the ring ( e ).
SKEMA 6
- OPERATING INSTRUCTION
2 for 20 seconds (this cycle is set as default
2 for 15 seconds.
2 for 20 seconds.
2 for 5 seconds, ramp from
2 for 5 seconds
2
for 5 seconds, ramp from
2
for 5 seconds, ramp from
2
for 10 seconds
GB EN 129 129 129