CASTELLINI SKEMA 6 CART Instructions De Service page 132

5.8. C-U2 intraoral camera system
C-U2 is an intraoral camera system specially designed for simple and well-conceived usability in examining the oral cavity complete with extremely lightweight
handpiece, auto-exposure and fi xed focus (version C-U2) or variable focus (version C-U2 Pro) features. This system is designed to facilitate dentist-patient
communication, to show and explain to patients all oral conditions and reasons for planned treatment so that they more clearly understand it. The C-U2 system
allows live images of the section in question to be taken through a touch of a fi ngertip on the touch-sensitive area of the handpiece. The live intraoral images
are displayed on the monitor or workstation.
ATTENTION!
The camera may be used as a tool to aid in diagnosis however, the result must always be compared to visual examination and/or other
diagnostic indications. Evaluations and conclusions based only on the image taken by the camera may be poor as the colors and shapes,
electronically processed, may not perfectly correspond to the actual ones.
Safety guidelines.
ATTENTION!
• The disposable infection control sheaths must be used with the device. Change the sheath for each new patient.
• After putting on a new disposable infection control sheath, check it over before using the camera, making sure it is not torn anywhere. If it is, take it off and
put on a new one.
• Do not place the handpiece in liquids or in autoclave under any circumstances.
• Store the handpiece in a clean dry area.
• Do not bend the connecting cable excessively.
• Be extremely careful not to drop the handpiece and do not expose it to excessive vibrations.
• Never use a damaged handpiece. Make certain the camera is in good condition and has no sharp edges before attempting to use it. If in doubt, do not use
the handpiece, carefully put it away and contact technical assistance.
• Before starting the equipment, check the condition of the lens protection.
• Do not direct the light beam in the operator's or patient's eyes during operation.
• During continuous use (example, more than 10 minutes consecutively), the temperature of the camera's tip usually increases signifi cantly; if this is uncomfor-
table, put the handpiece in its holder for a few minutes to allow the light source to cool down. When the camera needs to be used a prolonged time, reduce
the strength of the light emitted with the cursor on the OSD control panel (see paragraph 5.8.1).
• If left running for extended periods, make sure the temperature of the tip is acceptable before attempting to use the camera. Briefl y touch the clear plastic
part with your fi ngertip being careful not to touch the lens in the middle.
Connecting the handpiece.
Attach the handpiece of camera C-U2 ( a ) or C-U2 Pro ( c ) to the end of the
cord and tighten the knob ( b ).
ATTENTION!
Make sure the cord is fi rmly screwed onto the handpiece.
ATTENTION!
Make sure the cord is fi rmly screwed onto the handpiece.
Camera system usage.
• Put the instrument in its work position.
At this point the camera is on and may be in LIVE mode (the monitor shows
"live" images) or FREEZE mode (the last images frozen appear on the mo-
nitor), more precisely:
1- LIVE status in multi image mode
2 - FREEZE status in multi image mode
3 - LIVE status in single image mode
4 - FREEZE status in single image mode
NOTE: if the camera is in LIVE mode, the main screen is displayed
when the instrument is put back in place.
If the camera is in FREEZE mode, the relative menu remains on the monitor
when the instrument is put back into place.
• Briefl y press the foot control to stop from 1 to 16 images divided in 4 pages
on the monitor.
NOTE: the images shown on the monitor by the camera are only
temporarily saved. To permanently save the images, connect the camera
to a PC that complies to standard IEC 60950 which has a USB 2.0 HIGH
SPEED port and image software program.
132 132 132 GB EN
SKEMA 6
- OPERATING INSTRUCTION
1
3
2
ZOOM
4