Transmitter Setup - Hangar 9 P-51D Mustang Manuel D'utilisation

• TRANSMITTER SETUP

The receiver can be reprogrammed for use in future models. Reprogramming will remove the SAFE
programmied into the receiver, returning it to a standard Spektrum
be downloaded at http://www.spektrumrc.com.
: The included AR636 receiver has been programmed for operation specifi cally in this aircraft.
IMPORTANT
To operate the SAFE system in this aircraft, set up your optional DSM2/DSMX transmitter using the following chart.
• SAFE Flight mode is selected using Channel 5 signal (high, middle, low)
• Panic Recovery mode is selected with Channel 6 signal (high, low)
: A transmitter with a 2-position Channel 5 switch will only allow the use of position 0 or position 2 fl ight
IMPORTANT
modes. If possible (refer to your transmitter manual), assign Channel 5 in your transmitter to a 3-position switch to operate
all 3 fl ight modes.
Refer to your transmitter's manual for more information about transmitter setup.
Non Computerized Transmitter Setup
SAFE
Transmitter mode
switch
Throttle, Aileron, Elevator and Rudder in Normal Position
DX4e ACT/AUX
(2pos switch) switch
DX4e CH 5
(3pos switch) switch
DX5e CH 5
(2pos switch) switch
DX5e CH 5
(3pos switch) switch
® Technology features
AR636 receiver. The manual for the AR636 receiver can
™
(DX4e and DX5e)
SAFE Flight
Panic Recovery Switch
Modes Supported
Trainer Button 2 Pos Flight Mode
Trainer Button 3 Pos Flight Mode
Trainer Switch 2 Pos Flight Mode
Trainer Switch 3 Pos Flight Mode
Computerized Transmitter Setup
(DX6i, DX6, DX7S, DX8, DX9, DX10t and DX18)
Start all transmitter programming with a blank model (do a model reset), then name the model.
HIGH 100%
Set Dual Rates to:
LOW 70%
1. Go to the SETUP LIST MENU
DX6i
2. Set MODELTYPE: ACRO
3. Set REVERSE: Gear Channel
4. Go to ADJUST LIST MENU
5. Set TRAVEL ADJ: Gear/Fmode (0)
6. Set FLAPS: Norm 100; LAND
7. Set MIX 1: ACT; Gear Gear ACT, RATE D 0%; U + 100%, SW MIX, TRIM INH
Resulting in: The Gear and Mix switches operate the 3 SAFE modes
Gear 0; Mix 0 = Beginner Mode
Gear 1; Mix 0 = Intermediate Mode
Gear 1; Mix 1 = Advanced Mode
The Flap switch operates Panic Recovery:
Position 0=Off, Position 1=On. (not a momentary switch)
1. Go to the SYSTEM SETUP
DX7S
2. Set MODEL TYPE: AIRPLANE
DX8
3. Set SWITCH SELECT: Change all to INH then GEAR: AUX1, FLAP: GEAR
4. Go to the FUNCTION LIST
5. Set SERVO SETUP: Reverse AUX1
Resulting in: Flap/Gyro Switch operates the 3 SAFE modes (0 beginner/1
intermediate/2 advanced)
The Trainer/Bind button operates Panic Recovery
1. Go to the SYSTEM SETUP
DX6
2. Set MODEL TYPE: AIRPLANE
DX9
3. Set CHANNEL ASSIGN: click NEXT to go to Channel Input Confi g: GEAR: D, AUX1: i
DX10t
4. Go to the FUNCTION LIST
DX18
5. Set SERVO SETUP: Reverse AUX1
Switch D operates the 3 SAFE modes (0 beginner/
Resulting in:
1 intermediate/2 advanced)
The Bind/I button operates Panic Recovery
100%; Gear/Fmode (1) 40%
100
21