Vector Control - Lenze Global Drive 8200 vector Instructions De Montage
Masquer les pouces
Voir aussi pour Global Drive 8200 vector:
- Instructions de montage (250 pages) ,
- Instructions de montage (240 pages)
Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
8.5
Vector control
The following instructions apply to controllers equipped with a standard-I/O function module and a
three-phase AC motor which has been selected according to a power-based assignment.
Switch-on sequence
1.
Attach the keypad
2.
Ensure that controller inhibit is active after mains connection.
3.
Switch on the mains
4.
The keypad is in "Disp" mode after approx. 2 s and indicates the
output frequency (C0050)
5.
Change to the menu
ALL
6.
Change to the
mode to configure the basic settings for your
drive
7.
Adapt the terminal configuration to the wiring (C0007)
Lenze setting: 0, i. e.
E1: JOG1/3 fixed setpoint selection
E2: JOG2/3
E3: DCB DC brake
E4: CW/CCW operation
8.
Set the minimum output frequency (C0010)
Lenze setting: 0.00 Hz
9.
Set the maximum output frequency (C0011)
Lenze setting: 50.00 Hz
10.
Set the acceleration time T
Lenze setting: 5.00 s
11.
Set the deceleration time T
Lenze setting: 5.00 s
12.
Activate the control mode "vector control" (C0014 = 4)
Lenze setting: Linear V/f characterisitic control (C0014 = 2)
13.
Adapt the voltage/current range to the analog setpoint (C0034)
Lenze setting: 0, (0 ... 5 V/0 ... 10 V/0 ... 20 mA)
14.
Enter the motor data
A
Rated motor speed (C0087)
Lenze setting: 1390 rpm
B
Rated motor current (C0088)
Lenze setting: Depending on the controller
C
Rated motor frequency (C0089)
Lenze setting: 50 Hz
D
Rated motor voltage (C0090)
Lenze setting: Depending on the controller
E
Motor-cosϕ (C0091)
Lenze setting: Depending on the controller
L
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
(C0012)
ir
(C0013)
if
Commissioning
Note
}
Terminal X3/28 = LOW
X3
20
28
misc001
ON
misc002
The menu
d
c
b
e
a
1
Œ
j g f k i h PS
0050
000
‚
m n o
p
000
q
r
Hi
Hz
Lo
Blinking on the display:
z
d
c
b
e
a
w x
1
Œ
j g f
k
i h PS
0001
000
y
‚
m n o
p
0
q
r
Hi
Lo
z
d
c
b
e
a
1
w x
Œ
j g f k i h PS
0007
000
‚
m n o
p
y
0
q
r
Hi
Lo
[f]
C0011
C0010
0 %
100 %
f [ H z ]
C 0 0 1 1
f 2
f 1
0
t
t i r
t i f
T i r
T i f
z
d
c
b
e
a
w x
1
Œ
j g f k i h PS
001 4
000
‚
m n o
p
y
q
r
2
Hi
Lo
z
Set the DIP switch on the standard-I/O to the same
d
c
b
e
a
w x
1
Œ
j g f k i h PS
0034
000
‚
m n o
range (see Mounting Instructions for the
y
p
q
r
0
Hi
standard-I/O)
Lo
See motor nameplate
Enter the value for the motor connection type
(star/delta) selected!
Enter the value for the motor connection type
(star/delta) selected!
Vector control
USEr
is active
0001
C0011
T
= t
⋅
ir
ir
f 2 − f 1
t
= acceleration time wanted
ir
C0011
T
= t
⋅
if
if
f 2 − f 1
t
= deceleration time wanted
if
EDK82EV903 DE/EN/FR 2.2
99
Publicité
Chapitres
Table des Matières
