Vector Control - Lenze 8200 vector Instructions De Montage

Show/Hide Bookmarks Show/Hide Bookmarks
7
Commissioning

Vector control

The following instructions apply to the 8200 vector with function module Standard-I/O and the corres-
ponding three-phase AC motor
Switch-on sequence
1. Attach the keypad
2. Ensure that controller inhibit is
active after mains connection.
3. Switch on the mains
4. The keypad is in "Disp" mode after
approx. 2 s and indicates the output
frequency (C0050)
5.
Change to the menu
f
6.
Change to the
configure the basic settings for your
drive
7. Adapt the terminal configuration to
the wiring (C0007)
Lenze setting: -0-, i. e.
E1: JOG1/3 JOG frequency selection
E2: JOG2/3
E3: DCB DC brake
E4: CW/CCW operation
8. Set the minimum output frequency
(C0010)
Lenze setting: 0.00 Hz
9. Set the maximum output frequency
(C0011)
Lenze setting: 50.00 Hz
10. Set the acceleration time T
Lenze setting: 5.00 s Lenze setting: 5.00 s
11. Set the deceleration time T
Lenze setting: 5.00 s Lenze setting: 5.00 s
12. Adapt the voltage range/current
range to the analog setpoint (C0034)
Lenze setting: -0-, (0 ... 5 V/0 ... 10
V/0 ... 20 mA)
28
Œ
R m n o
Hi
Lo
A A A A L L L L L L L L ( ¶ 21)
z
mode to
w x
y
z
w x
y
C0011
C0010
(C0012)
ir
f [ H z ] f [ H z ] f [ H z ] f [ H z ]
C 0 0 1 1 C 0 0 1 1 C 0 0 1 1 C 0 0 1 1
f 2 f 2 f 2 f 2
f 1 f 1 f 1 f 1
(C0013)
if
0 0 0 0
z
w x
y
EDK82EV3 DE/EN/FR 2.0
@ ? > A =
j g f k i h PS
F
q r
Hz
@ ? > A
Œ
j g f k i h PS
R m n o
F
q r
Hi
Lo
@ ? > A
Πj g f k i h PS
R m n o
F
q r
Hi
Lo
[f]
0 %
100 %
t i r t i r t i r t i r t i f t i f t i f t i f
T i r T i r T i r T i r T i f T i f T i f T i f
@ ? > A
Πj g f k i h PS
R m n o
F
q r
Hi
Lo
Note
Terminal X3/28 = LOW
U U U U S S S S E E E E r r r r
The menu is active
The most important codes
A A A A L L L L L L L L
listed in the menu
explained in the code table.
( ¶ 31)
= Blinking on the display:
0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1
Hz
=
Hz
C0011
= t ⋅
T
ir ir
f 2 − f 1
t = acceleration time wanted
ir
C0011
= t ⋅
T
t t t t
if if
f 2 − f 1
t = deceleration time wanted
if
= Set the DIP switch on the
standard-I/O to the same
range (see Mounting
Hz
Instructions for the
standard-I/O)
L
are