Lenze Global Drive 8200 vector Instructions De Montage page 105

Commissioning
Code table
Code Possible settings
No. Name Lenze
C0007

uSEr
(cont.)
C0010 Minimum output
frequency
uSEr
C0011 Maximum output 50.00
frequency
uSEr
C0012 Acceleration time
main setpoint
uSEr
C0013 Deceleration time
main setpoint
uSEr
C0014 Operating mode

C0015 V/f rated frequency 50.00
uSEr
C0016 U boost
min
uSEr
C0034* Setpoint selection
range
Standard–I/O (X3/8)

uSEr
104
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Selection
E4
41 JOG1/3
42 QSP
43
CW/CCW
44 UP
45
CW/CCW
46
H/Re
47 CW/QSP
48
PCTRL1- OFF
49
PCTRL1- OFF
50
PCTRL1- OFF
51
DCB
255 Free configuration under C0410
0.00 0.00 {0.02 Hz}
14.5 Hz
7.50 {0.02 Hz}
87 Hz
5.00 0.00
5.00 0.00
2
2 V/f characteristic control V ~ f
(Linear characteristic with constant V
3 V/f characteristic control V ~ f
(Square-law characteristic with constant V
4 Vector control
5 Sensorless torque control with speed limitation
•
Torque setpoint via C0412/6
•
Speed limitation via setpoint 1 (NSET1-N1), if
C0412/1 is assigned, if not via max. frequency
(C0011)
7.50 {0.02 Hz}
0.00 {0.01 %}
0
0 Unipolar voltage 0 ... 5 V / 0 ... 10 V
Current 0 ... 20 mA
1 Current 4 ... 20 mA
2 Bipolar voltage -10 V ... +10 V
3 Current 4 ... 20 mA open-circuit monitored
EDK82EV903 DE/EN/FR 2.2
E3 E2 E1
DCB TRIP set DFIN1-ON
DCB TRIP set DFIN1-ON
QSP TRIP set DFIN1-ON
DOWN PAR DFIN1-ON
QSP PAR DFIN1-ON
PAR QSP JOG1/3
CCW/QSP H/Re JOG1/3
DCB DFIN1-ON
PCTRL1-I-OFF
JOG1/3 QSP DFIN1-ON
JOG1/3 DFIN1-ON
PCTRL1-I-OFF
PAR DFIN1-ON
PCTRL1-I-OFF
650.00
650.00
{0.02 s} 1300.00 Reference: frequency change 0 Hz ... C0011
{0.02 s} 1300.00 Reference: frequency change C0011 ... 0 Hz
boost)
min
2
boost)
min
960.00
40.00
IMPORTANT
Only display
Do not change C0007 since settings under
C0410 can be lost
•
C0010 is not effective with bipolar setpoint
selection (-10 V ... + 10 V)
•
C0010 only limits the analog input 1
Speed setting range 1 : 6 for Lenze
geared motors: Setting absolutely required
for operation with Lenze geared motors.
•
Additional setpoint C0220
•
Acceleration times can be activated via
digital signals C0101
•
Additional setpoint C0221
•
Deceleration times can be activated via
digital signals C0103
•
Commissioning without motor parameter
identification possible
•
Benefit of identification with C0148:
– Improved smooth running at low speed
– V/f rated frequency (C0015) and slip
(C0021) are calculated and stored. They
do not have to be entered
For initial selection enter the motor data
and identify the motor parameters with
C0148
Otherwise commissioning is not possible
•
C0015 is calculated and stored under C0148
when the motor parameters are identified
•
Settings applies to all possible mains
voltages
Depending on the controller
Setting applies to all mains voltages permitted
Observe the switch position of the function
module!
Changing the direction of rotation is only
possible with a digital signal.
•
Minimum output frequency (C0010) not
effective
•
Individual adjustment of offset and gain
TRIP Sd5, if I < 4 mA
Changing the direction of rotation is only
possible with a digital signal.
L