Ryobi RBV26 Manuel D'utilisation page 18

EN
FR DE ES
Idling ........................................................0.80 / 0.78 m/s
Equivalent vibration total value ..................0.96/0.93 m/s
Va c u u m m o d e ( F r o n t h a n d l e / r e a r h a n d l e )
Racing .....................................................1.63 / 1.60 m/s
Idling ........................................................0.80 / 0.76 m/s
Equivalent vibration total value ..................0.96/0.93 m/s
Uncertainty of vibration measurement .................1.5 m/s
KNOW YOUR BLOWER/VACUUM
See Figures 1a - 1b.
The safe use of this product requires an understanding of
the information on the tool and in this operator's manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all
operating features and safety rules.
BLOWER TUBE AND NOZZLES
The blower tube can be assembled and installed on the
blower without using any tools.
POSITIVE SWITCHES
The product is equipped with positive switches. The unit
will only run if both the metal contacts are inserted into
the positive switches. This reduces the risk of accidental
contact with rotating parts.
CRUISE CONTROL
The cruise control feature allows the user to operate the
blower without holding the throttle trigger. To slow the
en gine, simply push the cruise control lever forward.
HIGH VELOCITY NOZZLE WITH WET LEAF SCRAPER
The high velocity nozzle is great for wet sticky leaves. It
allows you to scrape wet leaves or debris while operating
the blower.
MOTOR
The blower has a powerful 26cc engine with sufficient
power to handle tough blowing and vacuuming jobs.
START EASY™
The Start Easy™ allows for easier and quicker starting.
THROTTLE TRIGGER
The blower can be operated at any speed between idle
and full throttle.
VACUUM / SILENCER
Converting the blower to a vacuum/silencer is simple and
can be done using a cross head screwdriver.
VACUUM BAG
The vacuum bag attaches to the blower easily by using
the vacuum bag adaptor.
VACUUM HANDLE
This feature allows user to perform vacuuming duties
comfortably.
IT PT NL SV DA
English(Original instructions)
NO FI HU CS RU
2
VACUUM TUBES
2
The vacuum tubes can be installed on the blower using a
cross head screw driver.
2
2
2
ASSEMBLY
2
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories
Q
from the box. Make sure that all items listed in the
packing list are included.
WARNING:
Do not use this product if any parts on the
Packing List are already assembled to your
product when you unpack it. Parts on this
list are not assembled to the product by the
manufacturer and require customer installation.
Use of a product that may have been
improperly assembled could result in serious
personal injury.
Inspect the product carefully to make sure no
Q
breakage or damage occurred during shipping.
Do not discard the packing material until you have
Q
care fully inspected and satisfactorily operated the
product.
ASSEMBLING THE BLOWER TUBES
See Figure 2.
Insert one end of the lower tube into one end of the
Q
upper tube.
Align raised tabs on blower housing outlet to the
Q
slots on upper tube; slide together and tighten
securely by twisting; press slider plate into positive
switch's slot to allow the positive switch to engage
and be ready to work. Check tightness after initial
use and retighten if needed.
Close the inlet cover and tighten the screw on the
Q
cover, making sure the metal contact is inserted into
the positive switch.
Pull out the slider from positive switch, then rotate
Q
the tubes to remove them from the blower housing
outlet.
INSTALLING THE VACUUM BAG
See Figures 3 - 4.
Remove blower tube from the blower by pulling off
Q
the metal contact, twisting and removing from the
blower housing outlet.
Unzip the vacuum bag and place the adaptor inside
Q
as shown. Push the vacuum bag adaptor through the
open ing opposite the zipper. The wider end of the
adaptor will remain on the inside of the vacuum bag
when installed properly.
Align the raised slots on the vacuum bag adaptor
Q
with the raised locking tabs on the blower housing
16
RO PL SL HR ET LT LV SK BG