Default Parameters - ero electronic FKS-MK1 Manuel De Service

1 . 4 Loop Break Alarm ( 1 . 4 1 . 4 1 . 4 1 . 4 Loop Break Alarm (LBA Loop Break Alarm ( Loop Break Alarm ( Loop Break Alarm ( LBA LBA LBA) function LBA ) function ) function ) function ) function
The functioning principle of this alarm is based on the concept that,
with a steady load and steady power output, the process rate of
rise (deviation/time) is steady as well.
The LBA function activates automatically when the adjustment
algorithm supplies the maximum power ("OLH") or the minimum
("OLL").
If the process response is slower than that set by parameters
"P57" and "P58", the instrument generates the "L.b.AL" alarm
indication in order to show that one or more element of the control
loop is in fault condition.
The indication is not subject to time out.
The alarm deactivates when the value of the control output varies
from min/max of a value greater than that of the hysteresis set by
parameter "P59". The parameters used in the LOOP BREAK
ALARM function can be set as described in the "Configuration
parameters Addendum" manual (from "P56" to "P61").
N O T E S : N O T E S : N O T E S : N O T E S : N O T E S :
a) The LBA alarm is not active during the soft start or if the control
output is disabled.
b) When the instrument operates with the SMART function, the
LBA may be operative.
fks-MK1-B1-A0.pmd 4

DEFAULT PARAMETERS

DEFAULT PARAMETERS DEFAULT PARAMETERS DEFAULT PARAMETERS DEFAULT PARAMETERS
2 . 1 2 . 1 2 . 1 2 . 1 2 . 1 I n t r o d u c t i o n I n t r o d u c t i o n I n t r o d u c t i o n I n t r o d u c t i o n I n t r o d u c t i o n
This chapter describes the default parameters for the
advanced configuration (from "P51" to "P66").
The parameters for the basic configuration (from "P1" to
"P18") are given in the "USER MANUAL" manual.
If, during configuration mode, the default value of the
parameters are loaded, the parameter from P51 to P66 will
be forced to their respective default value.
2 . 2 2 . 2 2 . 2Default values for advanced configuration Default values for advanced configuration Default values for advanced configuration Default values for advanced configuration
2 . 2 2 . 2 Default values for advanced configuration
p a r a m e t e r s p a r a m e t e r s p a r a m e t e r s p a r a m e t e r s p a r a m e t e r s
The parameters for the basic configuration (from "P1" to "P18")
are given in chapter 10 of the "Instructions for Use" manual.
TB1= European Table
TB2= American Table
P a r a m e t e r P a r a m e t e r TB1 value TB1 value TB2 value TB2 value
P a r a m e t e r P a r a m e t e r P a r a m e t e r TB1 value TB1 value TB1 value TB2 value TB2 value TB2 value
P 51 P 51 P 51 P 51 P 51 nonE nonE
P 52 P 52
P 52 P 52 P 52 Std Std
P 53 P 53 P 53 P 53 P 53 0 0
P 54 P 54 P 54 P 54 P 54 100% 100%
P 55 P 55 P 55 P 55 P 55 InF InF
P 56 P 56 P 56 P 56 P 56 nonE nonE
P 57 P 57 P 57 P 57 P 57 100 °C 180 °F
P 58 P 58 P 58 P 58 P 58 10.00 mm.ss 10.00 mm.ss
P 59 P 59 P 59 P 59 P 59 10 10
P 60 P 60 P 60 P 60 P 60 A. A.
P 61 P 61 P 61 P 61 P 61 rEV rEV
P 62 P 62 P 62 P 62 P 62 2.0% 2.0%
P 63 P 63 P 63 P 63 P 63 100.0% 100.0%
P 64 P 64 P 64 P 64 P 64 00.01 mm.ss 00.01 mm.ss
P 65 P 65 P 65 P 65 P 65 20.00 mm.ss 20.00 mm.ss
P 66 P 66 P 66 P 66 P 66 OFF OFF
B.4
09/05/2006, 10.06