Instrument In Unlock Mode; Instrument In Lock Mode; Configuration Parameters - ero electronic FKS-MK1 Manuel De Service

For conditions A) and C) press the REV + FUNC REV + FUNC REV + FUNC REV + FUNC REV + FUNC keys for
more than 3 sec. The display will shows "COnF COnF COnF COnF COnF".
Now the instrument is in mode D).
The next step is different according to the configuration
previously made.
5.2.1 5.2.1

5.2.1 Instrument in UNLOCK MODE

5.2.1 5.2.1 Instrument in UNLOCK MODE Instrument in UNLOCK MODE Instrument in UNLOCK MODE Instrument in UNLOCK MODE
a) The display will shows:
COnF OFF
and alternately
On
b) Press or to display and confirm with FUNC
The instrument goes in Configuration mode.
5.2.2 5.2.2 5.2.2 5.2.2 5.2.2

Instrument in LOCK MODE

Instrument in LOCK MODE Instrument in LOCK MODE Instrument in LOCK MODE Instrument in LOCK MODE
a) The display will shows:
COnF ----
and alternately
b) Press or until the value previously set in parameter
P18 (see section 5.3), or the "master key" value (see chap.
10 "Safety codes") are displayed.
Confirm with FUNC FUNC FUNC FUNC FUNC.
The instrument goes in Configuration mode.
N O T E S : N O T E S :
N O T E S : N O T E S : N O T E S :
a) If the value of P18 is 1, only the "master key" value allows a
change to Configuration mode.
fks-MK1-1-A0.pmd 6
5 . 3 5 . 3 Configuration 5 . 3 5 . 3 5 . 3 Configuration Configuration Configuration Configuration parameters parameters parameters parameters parameters
N O T E : N O T E : N O T E : N O T E : N O T E :
In configuration, the various parameters can always be
displayed, but they can only be changed if protection
hardware Sh2 is excluded (see Chap. 3 "Hardware
settings").
Some of the following parameter may be skipped according to
the valuie assigned to the previous parameters.
For each parameter, the instrument displays the reference
code and its value or status alternately. Press
the parameter value or status.
FUNC. FUNC FUNC FUNC
a) Press the FUNC FUNC pushbutton to save the new value and go FUNC FUNC FUNC
to the next parameter.
b) Press the REV REV REV pushbutton to return to the previous REV
REV
parameter without saving the new value of the current
parameter.
N O T E : N O T E : N O T E : N O T E : N O T E :
No timeout is active during Configuration mode
P 1 P 1 P 1 P 1 P 1
Type of input and standard range
* 1 = TC type L range
* 2 = TC type J range
* 3 = TC type K range
* 4 = TC type T range
5 = TC type N range
6 = TC type S range
7 = TC type R range
8 = TC type B range
9 = TC type W5 range
* 10 = RTD Pt100 range
11 = TC type L range
12 = TC type J range
13 = TC type K range
14 = TC type T range
15 = TC type N range
GB
6
09/05/2006, 15.06
or to modify
-100 / +900 °C
-100 / +1000 °C
-100 / +1370 °C
-200 / +400 °C
-100 / +1400 °C
-50 / +1760 °C
-50 / +1760 °C
0 / +1820 °C
0 / +2300 °C
-200 / +850 °F
-150 / +1650 °F
-150 / +1830 °F
-150 / +2500 °F
-330 / +750 °F
-150 / +2550 °F