ero electronic FKS-MK1 Manuel De Service page 91

P 6 0 P 6 0 P 6 0 P 6 0 P 6 0
"Loop Break Alarm" (LBA) reset "Loop Break Alarm" (LBA) reset "Loop Break Alarm" (LBA) reset "Loop Break Alarm" (LBA) reset "Loop Break Alarm" (LBA) reset
This parameter is available when at least one control output is
configured and "P56" is different from "nonE".
Range: A. = alarm with automatic reset
L. = alarm with manual reset
NOTE: NOTE:
NOTE: NOTE: NOTE: When the LBA output is in "or" on output 2 ("Out2")
together with Alarm 2, parameter "P60" will only be displayed.
The operating mode is selected by "P11".
P61 P61 P61 P61 P61
"Loop Break Alarm" (LBA) action "Loop Break Alarm" (LBA) action "Loop Break Alarm" (LBA) action "Loop Break Alarm" (LBA) action "Loop Break Alarm" (LBA) action
This parameter is available when at least one control output is
configured and "P56" is configured as "Out2".
Range: dir = direct action (the relay is energized or
SSr=1 in alarm condition)
rEV = reverse action (the relay is de-energized
or SSr=0 in alarm condition)
NOTE: NOTE: NOTE: NOTE: When the LBA output is in "or" on output 2 (P56 ="Out2") NOTE:
together with Alarm 2, parameter "P61" can only be monitored.
The operating mode is selected by "P12".
Minimum value of proportional band Minimum value of proportional band Minimum value of proportional band Minimum value of proportional band Minimum value of proportional band
P 6 2 P 6 2 P 6 2
P 6 2 P 6 2
calculated by the SMART function calculated by the SMART function
calculated by the SMART function calculated by the SMART function calculated by the SMART function
This parameter is available when at least one control output is
configured and the SMART function is configured ("P14"= "Enb"
or "Enb.P").
Range: from 2.0% at the value of "P63".
N O T E N O T E N O T E N O T E : N O T E
- the resolution of the value of "P62" will be 0.1% up to 10.0% and
1% up to 100.0%.
fks-MK1-B1-A0.pmd 3
Maximum value of proportional band Maximum value of proportional band Maximum value of proportional band Maximum value of proportional band Maximum value of proportional band
P 6 3 P 6 3 P 6 3 P 6 3 P 6 3
calculated by the SMART function calculated by the SMART function calculated by the SMART function calculated by the SMART function calculated by the SMART function
This parameter is available when at least one control output is
configured and the SMART function is configured ("P14"= "Enb"
or "Enb.P").
Range: from the value of "P62" at 100.0%.
N O T E N O T E N O T E : N O T E N O T E
- the resolution of the value of "P63" will be 0.1% up to 10.0% and
1% up to 100.0%.
Minimum value of integral time calcu- Minimum value of integral time calcu- Minimum value of integral time calcu- Minimum value of integral time calcu- Minimum value of integral time calcu-
P 6 4 P 6 4
P 6 4 P 6 4 P 6 4
lated by the SMART function lated by the SMART function lated by the SMART function lated by the SMART function lated by the SMART function
This parameter is available when at least one control output is
configured and the SMART function is configured ("P14"= "Enb"
or "Enb.P").
Range: from 00.01 mm.ss at the value of "P65".
Maximum value of integral time calcu- Maximum value of integral time calcu- Maximum value of integral time calcu- Maximum value of integral time calcu- Maximum value of integral time calcu-
P 6 5 P 6 5 P 6 5
P 6 5 P 6 5
lated by the SMART function lated by the SMART function
lated by the SMART function lated by the SMART function lated by the SMART function
This parameter is available when at least one control output is
configured and the SMART function is configured ("P14"= "Enb"
or "Enb.P").
Range: from the value of "P64" at 20.00 mm.ss
Automatic calculation of the "Relative Automatic calculation of the "Relative Automatic calculation of the "Relative
Automatic calculation of the "Relative Automatic calculation of the "Relative
P 6 6 P 6 6 P 6 6 P 6 6 P 6 6
cooling gain cooling gain cooling gain" " " " " cooling gain cooling gain
This parameter is available when the secondary control output
("Out2") and the SMART function are configured ("P14"= "Enb"
or "Enb.P").
Range: OFF = The Smart algorithm does not calculate the
relative gain value ("rC").
ON = The Smart algorithm calculates the relative
gain value ("rC").
The advanced configuration is finished. The instrument returns to
basic configuration (COnF).
B.3
09/05/2006, 10.06