Alternative Displays; Enabling/Disabling The Control Output - ero electronic FKS-MK1 Manuel De Service

6 . 6 . 6 . 6 . 6 . OPERATING OPERATING OPERATING OPERATING OPERATING MODE MODE MODE MODE MODE
During the operating mode the instrument performs the control
loop and manages all the functions (SMART, alarms, etc...).
At instrument power on in operative mode, the display shows
the measured value (we define this condition as "normal
display mode").
On switching on the instrument starts in the "mode" it was in
before switching off.
REV+FUNC REV+FUNC
If it starts in Configuration mode, press REV+FUNC REV+FUNC REV+FUNC for 3
seconds. The instrument will be resetted and it will started
again in operating mode.
6 . 1 6 . 1 6 . 1 6 . 1 6 . 1 Keyboard functions during operative mode Keyboard functions during operative mode Keyboard functions during operative mode Keyboard functions during operative mode Keyboard functions during operative mode
All the actions above explained which require the pressure
of two or more keys must follow exactly the keys equence
shown.
F U N C F U N C F U N C F U N C F U N C During the parameter modification
procedure, saves the new value of the
parameter selected and goes to the next
parameter (increasing order).
When the instrument is in "normal display
mode", if pressed for more than 3 sec.,
changes the display indication (see
"Alternative display functions". Sect. 6.1).
R E V R E V R E V During parameter modification, it allows to scroll
R E V R E V
back the parameters without memorizing the
new setting.
When the instrument is in "normal display
mode", if pressed for more than 3 sec.
starts/stops the SMART function (see section
6.7).
FUNC FUNC FUNC
+ FUNC FUNC
When the instrument is in "normal display
mode", if pressed for more than 3 sec.
disables/disables the control output (see
"Enabling / Disabling the control output"
section 6.5).
+ FUNC FUNC FUNC FUNC FUNC
When the instrument is in "normal display
mode", enables the Lamp Test function (see
"Lamp Test", section. 7.1).
fks-MK1-1-A0.pmd 12
Increases the value of the selected
parameter. Keeping the pushbutton
pressed, the variation speed is increased.
Decreases the value of the selected
parameter. Keeping the pushbutton
pressed, the variation speed is increased.
+ When the instrument is in "normal display
mode", reload the default values of the
operative parameters (see chap. 10 "Default
parameters")
REV + FUNC REV + FUNC REV + FUNC
REV + FUNC REV + FUNC
When the instrument is in "normal display
mode", if pressed for more than 3 sec.,
switches from the configuration procedure to
the operating procedure or vice versa.
N O T E N O T E N O T E N O T E N O T E :
During operative mode, a timeout of 10 or 30 seconds
(see parameter "P17" in "Configuration") is applied to the
parameters modification.
If when modifying a parameter, no pushbutton is
pressed for a time longer than the timeout (10 or 30
seconds), the instrument automatically returns to "normal
display mode" losing any modification of the last
parameter selected.
6 . 2 Alternative 6 . 2 6 . 2 6 . 2 6 . 2 Alternative Alternative Alternative Alternative displays displays displays displays displays
From the normal display mode, it is possible to change the
information shown on the display in the following way:
a) On pressing the FUNC FUNC key for more than 3 sec., the display FUNC FUNC FUNC
will show the status of alarm LBA (if configured) as follows:
"L.b.OF" = no allarm
"L.b.AL" = alarm condition
b) On pressing the FUNC key again the display will show the set
point value. The decimal point indicated in Fig. 10 is ON.
Fig. 10
Control output value Set point
GB
12
09/05/2006, 15.06