Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
P 8
P 8
P 8
P 8
P 8
Alarm 1: action
Alarm 1: action
Alarm 1: action
Alarm 1: action
Alarm 1: action
This parameter is only available if output 1 is configured as
alarm 1 ("P6" = "ALr.1")
Range:
dir
= direct action (the relay is energized or
SSr=1 in alarm condition)
rEV
= reverse action (the relay is de-energized
or SSr=0 in alarm condition)
P 9
P 9
P 9
P 9
P 9
Alarm 1:
Alarm 1:
Alarm 1: standby function
Alarm 1:
Alarm 1:
standby function
standby function
standby function
standby function
This parameter is only available if output 1 is configured as
alarm 1 ("P6" = "ALr.1")
Range:
OFF
= standby function disabled
ON
= standby function enabled
N O T E :
N O T E
N O T E
N O T E
N O T E
- The standby function can "mask" an alarm condition on
switching on, until the process variable reaches the alarm
threshold plus or minus the hysteresis.
P 1 0
P 1 0
P 1 0
P 1 0
P 1 0
Function of output 2 (secondary)
Function of output 2 (secondary)
Function of output 2 (secondary)
Function of output 2 (secondary)
Function of output 2 (secondary)
Range:
nonE
= Output not used
nALF
= Output to signal a fault condition
detected on the measurement
Proc
= Alarm 2 output - Process alarm
bAnd
= Alarm 2 output - Band alarm
dEV
= Alarm 2 output - Deviation alarm
CooL
= Output used for the cooling in the
configuration with two control outputs.
N O T E S :
N O T E S :
N O T E S :
N O T E S :
N O T E S :
a) If "bAnd" or "dEV" have been selected, parameter "P6" is
forced to "rEV" if "ALr.1" is set.
b) If a type of alarm is selected, threshold "AL.2" is checked
and, if out of range, forced to the default value.
fks-MK1-1-A0.pmd
9
c) Setting "P10" equal to "CooL":
1 "P6" will be forced to "rEV".
2 "OLL" will be forced to -100 and "OLH", if smaller than
or equal to zero, will be forced to 100.
3 "IP" will be forced to zero.
d) If output "CooL" is removed, the instrument performs
the action described in parameter "P6" (note a).
P11 1 1 1 1
P1
P1
P1
P1
T T T T T ype of cooling media or operating mode
ype of cooling media or operating mode
ype of cooling media or operating mode
ype of cooling media or operating mode
ype of cooling media or operating mode
alarm 2
alarm 2
alarm 2
alarm 2
alarm 2
This parameter is only available if "P10" is different from
"nonE".
When "P10" is different from "CooL":
When "P10" is different from "CooL":
When "P10" is different from "CooL":
When "P10" is different from "CooL":
When "P10" is different from "CooL":
Range:
H.A.
= High alarm (outside for band alarm) with
automatic reset.
L.A.
= Low alarm (inside for band alarm) with
automatic reset.
H.L.
= High alarm (outside for band alarm) with
manual reset.
L.L.
= Low alarm (inside for band alarm) with
manual reset
N O T E : The "high or low" selection has no effect if the
N O T E
N O T E
N O T E
N O T E
output is used as fault signaller.
When "P10" is equal to "CooL":
When "P10" is equal to "CooL":
When "P10" is equal to "CooL":
When "P10" is equal to "CooL":
When "P10" is equal to "CooL":
Range:
If "P10" is set to "CooL":
Air
= The cooling media is air
OIL
= The cooling media is oil
H2O
= The cooling media is water.
N O T E
N O T E :
N O T E
N O T E
N O T E
- Varying the type of cooling, parameters "C2" and "rC" will be
forced to the relative default values.
GB
9
09/05/2006, 15.06
Publicité
Table des Matières
