Instrument Configuration - ero electronic TKS Manuel De Service

c) Push "FUNC" push-button. The instrument ends the
configuration modify mode, preforms an automatic
reset and restarts in the run time mode.
Pushbutton function during configuration mode Pushbutton function during configuration mode Pushbutton function during configuration mode Pushbutton function during configuration mode Pushbutton function during configuration mode
FUNC = This will memorize the new value of the selected
parameter and go to the next parameter
(increasing order).
MAN = This will scroll back the parameters without
memorization of the new value.
= This will increase the value of the selected
parameter
= This will decrease the value of the selected
parameter.
CONFIGURATION PARAMETERS CONFIGURATION PARAMETERS CONFIGURATION PARAMETERS CONFIGURATION PARAMETERS CONFIGURATION PARAMETERS
Notes: Notes: Notes:
Notes: Notes:
1 ) In the following pages we will describe all the
parameters of the instrument but the instrument will
show only the parameters related with the specific
hardware and in accordance with the specific
instrument configuration (i.e. setting OUT 3 equal to 0
(not used), all the parameters related with alarm 2 will
be skipped).
2 ) During configuration mode, the lower display shows
the mnemonic code of the selected parameter while
the upper display shows the value or the status
assigned to the selected parameter.
dF.Cn = Default configuration parameter dF.Cn = Default configuration parameter dF.Cn = Default configuration parameter dF.Cn = Default configuration parameter dF.Cn = Default configuration parameter
loading loading loading loading loading
Available in modify configuration parameters only
OFF = No loading data
tb1 = Loading European Table default parameters.
tb2 = Loading American Table default parameters.
NOTE: NOTE: NOTE: the list of both default parameter tables is reported at NOTE: NOTE:
Appendix A.
XKS-1-B0.pmd 9
SEr1 = Serial interface protocol SEr1 = Serial interface protocol SEr1 = Serial interface protocol SEr1 = Serial interface protocol SEr1 = Serial interface protocol
OFF = No serial interface
Ero = Polling/selecting ERO
nbUS = Modbus
jbUS = Jbus
SEr2 = Serial link device address SEr2 = Serial link device address SEr2 = Serial link device address SEr2 = Serial link device address SEr2 = Serial link device address
Not available when SEr1 = OFF
From 1 to 95 for ERO protocol
From 1 to 255 for all the other protocols
NOTE NOTE: the electrical characteristic of the RS 485 serial NOTE NOTE NOTE
interface will allow the connection of 31 devices maximum.
SEr3 = Baud rate for serial link SEr3 = Baud rate for serial link SEr3 = Baud rate for serial link SEr3 = Baud rate for serial link SEr3 = Baud rate for serial link
Not available when SEr1 = OFF
From 600 to 19200 baud.
NOTE NOTE: 19200 baud is shown on display as 19.20. NOTE NOTE NOTE
SEr4 = Byte format for serial link SEr4 = Byte format for serial link SEr4 = Byte format for serial link SEr4 = Byte format for serial link SEr4 = Byte format for serial link
Not available when SEr1 = OFF
7E = 7 bits + even parity (For ERO protocol only)
7O = 7 bits + odd parity (For ERO protocol only)
8E = 8 bits + even parity
8O = 8 bits + odd parity
8 = 8 bits without parity
P1 - Input type and standard range P1 - Input type and standard range P1 - Input type and standard range P1 - Input type and standard range P1 - Input type and standard range
0 = TC type L range
1 = TC type L range
2 = TC type J range -100.0 /
3 = TC type J range -100 /
4 = TC type K range -100.0 /
5 = TC type K range -100 /
6 = TC type N range -100 /
7 = TC type R range
8 = TC type S range
9 = RTD type Pt 100 range -199.9 /
10 = RTD type Pt 100 range -200 /
11 = mV Linear range
12 = mV Linear range
13 = mA Linear range
GB GB
GB GB GB 9
20/06/2005, 13.41
0 / +400.0 °C
0 / +900 °C
+400.0 °C
+1000 °C
+400.0 °C
+1370 °C
+1400 °C
0 / +1760 °C
0 / +1760 °C
+400.0 °C
+800 °C
0 / 60 mV
12 / 60 mV
0 / 20 mA