ero electronic TKS Manuel De Service page 19

P23 = action of: the Alarm 2, the "Out 1 failure P23 = P23 = P23 = P23 = action of: the Alarm 2, the "Out 1 failure action of: the Alarm 2, the "Out 1 failure action of: the Alarm 2, the "Out 1 failure action of: the Alarm 2, the "Out 1 failure
detection" function and of the "Loop break detection" function and of the "Loop break detection" function and of the "Loop break detection" function and of the "Loop break detection" function and of the "Loop break
alarm" function. alarm" function. alarm" function. alarm" function. alarm" function.
Available only when P12 is different from 0 or P10 is different
from "OFF" or P47 is different from dIS.
dir = direct (relay energized in alarm condition)
rEV = reverse (relay de-energized in alarm condition)
P24 = Alarm 2 stand-by function (mask alarm) P24 = Alarm 2 stand-by function (mask alarm) P24 = Alarm 2 stand-by function (mask alarm) P24 = Alarm 2 stand-by function (mask alarm) P24 = Alarm 2 stand-by function (mask alarm)
Available only when P12 is different from 0.
OFF = stand-by function (mask alarm) disabled
On = stand-by function (mask alarm) enabled
NOTE NOTE
NOTE NOTE NOTE: see NOTE about P22 parameter.
P25 = Alarm 3 action P25 = Alarm 3 action P25 = Alarm 3 action P25 = Alarm 3 action P25 = Alarm 3 action
Available only when P14 is different from 0.
dir = direct (relay energized in alarm condition)
rEV = reverse (relay de-energized in alarm condition)
P26 = Alarm 3 stand-by function (mask alarm) P26 = Alarm 3 stand-by function (mask alarm) P26 = Alarm 3 stand-by function (mask alarm) P26 = Alarm 3 stand-by function (mask alarm) P26 = Alarm 3 stand-by function (mask alarm)
Available only when P14 is different from 0.
OFF = stand-by function (mask alarm) disabled
On = stand-by function (mask alarm) enabled
NOTE NOTE NOTE NOTE: see NOTE about P22 parameter. NOTE
P27 = OFFSET applied to the measured value P27 = OFFSET applied to the measured value P27 = OFFSET applied to the measured value P27 = OFFSET applied to the measured value P27 = OFFSET applied to the measured value
It allows to set a constant OFFSET throughout the readout
range. It is skipped for linear inputs
- For readout ranges with decimal figure, P27 is
programmable from -19.9 to 19.9.
- For readout ranges without decimal figure, P27 is
programmable from -199 to 199.
Readout
Real curve
P27
Adjusted
curve
Input
XKS-1-B0.pmd 13
P28 = NOT AVAILABLE P28 = NOT AVAILABLE P28 = NOT AVAILABLE P28 = NOT AVAILABLE P28 = NOT AVAILABLE
P29 = Displayable protected parameters P29 = Displayable protected parameters P29 = Displayable protected parameters P29 = Displayable protected parameters P29 = Displayable protected parameters
This parameter is skipped when P20 = 0.
OFF = Protected parameters cannot be displayed.
On = Protected parameter can be displayed.
P30 = MANUAL function P30 = MANUAL function P30 = MANUAL function P30 = MANUAL function P30 = MANUAL function
OFF = manual function is disabled
On = manual function can be enabled/
disabled by MAN pushbutton.
P31= SMART function P31= SMART function P31= SMART function P31= SMART function P31= SMART function
0 = SMART function disabled.
1 = SMART function is NOT protected by safety lock.
2 = SMART function is under safety lock protection.
P32 = P32 = P32 = P32 = P32 = Relative cooling gain calculated by SMART Relative cooling gain calculated by SMART Relative cooling gain calculated by SMART Relative cooling gain calculated by SMART Relative cooling gain calculated by SMART
function. function. function. function. function.
This parameter is available only when P7 = 4 and P31 is
different from 0.
OFF = SMART algorithm does not calculate the rC
parameter value
On = SMART algorithm calculates the rC parameter
value.
P33 = P33 = P33 = P33 = P33 = Maximum value of the proportional band Maximum value of the proportional band Maximum value of the proportional band Maximum value of the proportional band Maximum value of the proportional band
calculated by the SMART algorithm. calculated by the SMART algorithm. calculated by the SMART algorithm. calculated by the SMART algorithm. calculated by the SMART algorithm.
This parameter is skipped if P31=0.
It is programmable from P34 or P35 value to
100.0 %.
P34 = P34 = P34 = P34 = P34 = Minimum value of the proportional band Minimum value of the proportional band Minimum value of the proportional band Minimum value of the proportional band Minimum value of the proportional band
calculated by the SMART algorithm when the calculated by the SMART algorithm when the calculated by the SMART algorithm when the calculated by the SMART algorithm when the calculated by the SMART algorithm when the
instrument has two control outputs. instrument has two control outputs. instrument has two control outputs.
instrument has two control outputs. instrument has two control outputs.
This parameter is available only when P7 = 4 and P31 is
different from 0.
It is programmable from 1.5% to P33 value.
GB GB
GB GB GB 13
20/06/2005, 11.09