Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
107
Then cut the
e strips roug
hly to length
an even dis
stance betwe
een the strips
Cut and grin
nd the strip e
ends on the o
The gangwa
ay is made fr
rom the sam
In the case
of grating "A
A" (106), rece
shown in th
e plan.
Rotate the l
asered lid (5
52) on the for
Now align th
he grating "A
A" according
For secure f
fastening of
the cover an
self-tapping
g screws (110
0). For this p
the cover w
with Ø 2.5 mm
m. Insert the
been remov
ved from the
foot on the c
cover and al
ign it so that
and photo).
Then mark
the 3 holes o
of the foot on
(Mo2) is now
w screwed to
o the cover w
to remain rig
gid, then dril
l out the bea
the foot).
Now solder
the guide tu
be (Mo5) on
protrudes a
bout 5 mm fr
rom the shaf
1 mm tube s
so that the fi
ne hole at th
tube, which
should not r
rub through!
Now place t
the rotary he
ead (Mo6) on
mm hole of
the rotary he
ead. Glue sh
The pipe ho
olders (Mo7)
the extingui
shing water
pressure is a
(Mo9) made
e of aluminiu
m pipe, the s
in the rotary
y head and in
n the pipe ho
Adjust the p
parts so that
they can be
together wit
th a small dro
op of superg
(Mo12) into
the slots of
the rotary he
glue on the
varnished st
traightening
Insert the sp
piral spring (
Mo14) (Ø 3.2
for monitor
"A", and plac
ce the hose o
slipping with
h a drop of s
uperglue and
A piece of w
wire that is be
ent into a sm
hook into th
he end of the
fits easily in
nto the Ø 7 m
mm tube.
Cut off the e
end of the ho
ose so that th
The spring i
in the hose p
prevents it fro
14
109
1
Rest 1 m
m
h according to
o the photo a
s, hold a 1 m
m thick ABS
outer contou
me slats (109)
) according t
esses must b
be provided f
rebody so th
at the deck s
to the plan s
straight and i
nd the later m
mounted mon
purpose, the
lid and deck
bearing bush
hing (Mo1) in
deck from b
elow as cent
tring. Glue th
t the housing
g (Mo3) point
n the cover a
and drill Ø 2 m
with M 2 x 10
0 brass screw
aring bushing
g (Mo1) (A 2
n top into the
ft. Cut off the
e bottom Mo5
he edge is nic
cely smooth.
n the shaft (M
Mo4) so that t
haft and head
d together wi
are to be glu
ued cleanly a
and precisely
applied to the
em later. Ins
spray nozzle
e (Mo10) and
older so that
easily move
glue. Check a
again for eas
ead, align the
em at an ang
lever (Mo13)
).
2 x 60 mm) i
into the silico
on the conne
ection nipple
d then pull it
mall hook at t
he end is rec
hose and pu
ull in the hos
se. By slightly
he hole in the
e front of the
om buckling.
. Check easy
© Kla
aus Krick Mo
odelltechnik,
and glue them
waste piece
e in between
r and the inn
ner, round op
pening.
o the plan.
for the fasten
ning screws (
structure (tul
n the middle
e. Glue the lid
nitor, the enti
are drilled to
ogether with
nto the Ø 15
he housing (M
ts exactly in t
mm. If the m
ws (111) and
d M2 nuts (11
mm) under t
monitor sha
aft (Mo4) (for
5 flush, but d
do not solder
. (Later, a ny
ylon thread is
the thin tube
e (Mo5) lies la
ith superglue
e.
y with superg
glue. The sea
sert the foam
d glue (super
rglue). Place
the thin tube
e (Mo5) is on
d up and dow
wn, and then
n glue the pip
se of moveme
gle to the rea
ar and glue th
one hose (Mo
of the pipe h
holder. Secu
into the mon
nitor shaft.
commended
y stretching t
e hose does n
y movement
Knittlingen, G
m to the grat
ting frames.
.
(110) at the p
le) matches
the structure
e on the lid.
d and grating
ire assembly
y is fastened
Ø 1.5 mm. T
mm opening
g in the cove
Mo3) to the b
base (Mo2).
the direction
of the gratin
ng. (see map
onitor "A" is
to be pivoted
12). (If the m
the ceiling! a
and screw it t
monitor "A"
120 mm long
it. Cleanly d
deburr the Ø
s passed thro
aterally left in
ams must be
e sealed, as
pipe (Mo8),
the extingui
the pipe ben
the left in th
he direction o
of injection.
pe holder an
ent. Now ins
sert the two o
outriggers
hem together
o15), which i
is about 300
re the hose
as an aid fo
r pulling in. H
the hose diam
meter decrea
not leak.
of the entire
extinguishin
ng head, as
Germany
Status 08
8/2022
To achieve
points
g together.
with the 3
Then drill out
t
r which has
Place the
p
d, the base
onitor "A" is
together with
h
g) so that it
ough this
n the Ø 7
shing pipe
nds (Mo11)
d pipe bend
r. Finally,
mm long
against
Hang the
ases and
Publicité
Table des Matières
