Krick ro marin Dusseldorf Mode D'emploi page 48

Anchor win ndlass:
The 3 winch h housing pa arts (70) are d
If necessary y, re-drill the
Cleanly san nd and prime e the part. Aft
Now bend t he 3 cranks (74) accordi
them into th he axles (71)
to the axle ( (78) and fit a a washer (79)
chain whee l with axle, p push on the s
rotate easily y inside the h housing. The
knob (81).
Drill Ø 3 mm m for the cha ain links (82)
stoppers (83 3). First drill the holes in
the crank. F Fit the cranks s (84) with 2
Glue under the 4 x 4 mm m ABS unde
positioning are adjusted d so that the a
capstan hea ad through th he chain stop
If the windla ass is to be d dismantled, t
In the other case now p rovide the tw
and glue the em in the cha ain pins 82 (
Working anchor w indlass fo
91
92
95a a
In order to a avoid entang gling of both a
only one an nchor function nal.
89
88
12
detached fro om the laser s
Ø 2 mm hol e for the cra nk shaft (71)
ter the base plate (73) ha
ng to the dra awing, solder
and (76). So older the sec cond sleeve (
). Insert the s sleeve (72) i
second wash her (79) and g
en fit the pre- -assembled c
according to o the plan an
the longitudi inal direction
sleeves (75) ) each and s
rlay (85) acc cording to the
anchor chain ns can be gu
ppers to the anchor tubes
he following
wo anchors (8 86) with 100
UHU hart).
or one anc chor
96
anchor chain ns in later fun
90
© Kla aus Krick Mo odelltechnik,
sheet and gl
) and the Ø 2 2.5 mm hole
as been glue ed on, paint th
r or glue them m to the han
(72) to the ax
nto the winch h housing (7
glue on the c capstan head
crank axles ( (71) and (76)
d glue on the e rivet. Now
n Ø 3 mm, the en drill the Ø
lide them into o the right an
e detailed dra awing. The s
uided in a stra aight line fro
s (55).
section mus st be followed d.
mm chain (8 87) each, pu
88
99
9
97
98
1 117
103
nctional oper ration, it is re
Th he right anch hor is shown
thi is case, the l left anchor m
Gl lue the lasere ed base plat
fra ame (89) and d the upper f
the e plan. Finis h the base p
be e easily inser rted into the f
blo ocks (92) wit th reinforcem
sh horter slots o
Knittlingen, G Germany
ued together r (UHU hart)
for the one s
he finished h housing.
dles (75) and
xle (76). Glu e the chain w
0), push thro ough the
d (80). The u unit must
) and insert t
remove the
Ø 2 mm cross
nd left chain
slope to the d deck and the
m the sprock
ll them in as
89
6 92
102
ecommended d to make
functional in
must be shut
te (88) to the
rame (90) ac ccording to
plate (91) so t
frame. Glue
ment strips (9 93) into the
f the base pl late. Glue the
Status 08 8/2022
.
sleeve 72.
d insert
wheel (77)
the gear
chain
s hole for
stoppers.
e
ket and
planned
90
94
95 5
the plan. In
down.
lower
that it can
the bearing
e motor