After operation with detergent
1. Pull the Plug 'n' Clean detergent bottle out of the
holder and close it with the lid.
2. For storage, place the detergent bottle in the holder
with the lid facing upwards.
3. Rinse the device with clean water for about 30 sec-
onds.
Interrupting operation
1. Release the lever of the high-pressure gun.
When the lever is released, the device switches off.
The high-pressure in the system is maintained.
2. Lock the lever of the high-pressure gun.
Illustration N
3. Set the high-pressure gun with the spray lance in
the parking position.
4. For work breaks longer than 5 minutes, switch off
the device "0/OFF".
Ending operation
CAUTION
Danger of injury!
Injuries due to uncontrolled water escaping under high
pressure.
Only disconnect the high-pressure hose from the high-
pressure gun or the device if there is no pressure in the
system.
CAUTION
Risk of scalding!
Scalding due to hot water escaping after operation,
when disconnecting the garden hose or high-pressure
hose.
Wear suitable protective gloves.
After operation, allow the device to cool down before
disconnecting the garden hose or high-pressure hose.
1. Release the lever of the high-pressure gun.
2. Close the water tap.
3. Press the lever of the high-pressure gun for 30 sec-
onds.
The pressure in the system is released.
4. Release the lever of the high-pressure gun.
5. Lock the lever of the high-pressure gun.
6. Switch off the device "0/OFF".
7. Disconnect the device from the water supply.
8. Pull the mains plug out of the outlet.
Transport
CAUTION
Risk of injury or damage due to the weight of the de-
vice!
Injury and damage.
Be aware of the weight of the device during transport
and storage.
Carrying the device
1. Lift up the device by the carrying handle, and carry
it.
Pulling device
1. Pull out the transport handle until it audibly engages.
2. Pull the device by the transport handle.
Transporting the device in a vehicle
1. Before horizontal transport, pull the Plug 'n' Clean
detergent bottle out of the holder and close it with
the lid.
2. Secure the device against shifting and tipping.
18
CAUTION
Risk of injury or damage due to the weight of the de-
vice!
Injury and damage.
Be aware of the weight of the device during transport
and storage.
Storing the device
1. Place the device on a level surface.
2. Disconnect the spray lance from the high-pressure
gun.
3. Press the separation button on the high-pressure
gun and disconnect the high-pressure hose from the
high-pressure gun.
4. Without a hose reel: Store the high-pressure hose
on the device.
ATTENTION
Damage to the high-pressure hose
Damage to the high-pressure hose through incorrect di-
rection of rotation
Observe the correct direction of rotation of the hose reel
when winding on the hose.
5. With a hose reel: Use the crank handle to turn the
hose reel counterclockwise and wind up the high-
pressure hose.
6. Stow the mains connection and accessories on the
device.
Before prolonged storage, observe additional instruc-
tions, see chapter Care and service.
ATTENTION
Danger of frost
Incompletely emptied devices can be destroyed by
frost.
Completely empty the device and accessories.
Protect the device from frost.
The following must be met:
● The device is disconnected from the water supply.
● The high-pressure gun is separated from the high-
pressure hose.
1. Switch on the device "I/ON".
2. Wait a maximum of 1 minute until no more water
comes out of the high-pressure hose.
3. Switch off the device.
4. Store the device with all accessories in a frost-proof
room.
Care and service
DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
The device is maintenance-free, i.e. you do not need to
perform any maintenance work.
Clean the sieve in the water connection
ATTENTION
Risk of damage!
Damage to the sieve due to improper cleaning.
Clean the sieve only under running water against its
flow direction.
Do not use sharp or hard objectse.g. needles or wire
brushes.
English
Storage
Frost protection