Video Setup; Troubleshooting - Rotel RSP-1576MKII Manuel De L'utilisateur

NETWORK CONFIGURATION
IP ADDRESS MODE
RENEW DHCP IP ADDRESS
VIEW NETWORK SETTINGS
TEST NETWORK CONNECTION
BACK
SOFTWARE INFORMATION: Displays the current software installed in the
unit. It shows the MAIN, DSP and STANDBY software versions. There is also
an option to check for software updates. This feature lets the unit search
for software updates on the Internet. The network needs to be properly
configured. Alternatively, you can load the software through the front USB
socket. For more information on the software update process please contact
your authorized Rotel dealer.
RESTORE FACTORY DEFAULT: This option sets the unit back to the original
setting as when it left the factory. All user settings will be erased.
NOTE: Use caution when resetting the RSP-1576MKII to factory defaults
as all user configured options will be erased and reset to original
factory settings.

Video Setup

VIDEO SETUP
STANDBY VIDEO SOURCE
FAST AUDIO SYNC
OSD FORMAT
BACK
The VIDEO SETUP menu provides configuration of the HDMI outputs. See
the HDMI INPUTS & OUTPUTS section of this manual for details on HDMI
connections.
STANDBY VIDEO SOURCE: Options are "DISABLE", "HDMI 1-6", "HDMI
FRONT", or "LAST". This allows the selected HDMI source input to pass-
through the RSP-1576MKII while in standby mode. Audio and video are
passed directly to the attached TV or display.
NOTE: When the Standby Video Source is enabled the RSP-1576MKII
will consume additional power when in standby mode.
NOTE: Signal Sense power control is disabled with STANDBY VIDEO
SOURCE is enabled.
FAST AUDIO SYNC: This function allows the HDMI audio to sync more quickly
with the RSP-1576MKII. Only 1 input can be selected for this function.
NOTE: Some source devices do not provide the timing requirements to
allow this function to work properly and could result in static noise before
the audio is heard.
DHCP
DISABLE
DISABLE
480P
OSD FORMAT: The HDMI On Screen Display output resolution can be
changed from 480P to 576P. The default value is 480P.
Press the BACK button or select "BACK" on the OSD to exit the VIDEO
SETUP Menu and return to the main menu.

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the problem
area, check the control settings, determine the cause of the fault and make
the necessary changes. If you are unable to get sound from the unit, refer
to the suggestions for the following conditions:
The unit does not turn on
• Make sure the power cord is plugged into the rear panel and a AC outlet.
• Make sure the rear panel POWER switch is in the ON position.
No sound from any input
• Make sure that MUTING is off and VOLUME is turned up.
• Make sure source inputs are connected and configured correctly.
No sound from digital sources
• Make sure that digital input connector is assigned to the proper source
input and that the source input is configured to use the digital input
rather than an analog input.
• Check the configuration of the digital input source player to ensure
that the digital output is activated.
No sound from some speakers
• Check all power amp and speaker connections.
• Check Speaker Configuration settings in the Setup menus.
No Video Output
• Make sure that the TV monitor is connected properly and check the
input assignments.
• Check the source input and TV output resolution are compatible. A 4K
source can only be sent to a 4K monitor.
• HDMI cables must be 5 meters or less in length.
• If watching 3D sources, make sure the display is 3D enabled.
Video and Audio do not match.
• Check that the proper video source is selected for each input.
• Check that the group delay (lip-sync) setting is not mis-adjusted.
Clicking or popping sounds when switching inputs
• The unit uses relay switching to preserve maximum sound quality. The
mechanical clicking of the relays is normal.
• Switching between HDMI sources may cause delays as HDMI two way
communications "handshake" must be established between the source
27