Siemens SINUMERIK 840D sl Manuel De Mise En Service page 342

Mise en service HMI-Embedded (IM2)
4 Fonctions/Paramétrage
9650 CMM_POS_COORDINATE_SYSTEM
- Position du système de coordonnées
SM, ST, Adv, SM: 0, ST: 34,
Emb Adv: 0, Emb: 0
9651 CMM_TOOL_MANAGEMENT
- Concept de gestion d'outils
SM, ST, Adv, SM: 4, ST: 4,
Emb Adv: 4, Emb: 4
9652 CMM_TOOL_LIFE_CONTROL
- Surveillance d'outil
SM, ST, Adv, SM: 1, ST: 1,
Emb Adv: 1, Emb: 1
9661 CMM_ENABLE_CUSTOMER_M_CODES
- Introduction d'instructions M spécifiques au client
SM, ST, Adv, SM: 0, ST: 0,
Emb Adv: 4, Emb: 0
9663 CMM_TOOL_DISPLAY_IN_DIAM
- Affichage du rayon/diamètre d'outil
SM, ST, Adv, SM: 1, ST: 1,
Emb Adv: 1, Emb: 1
9672 CMM_FIXED_TOOL_PLACE
- Codage d'emplacement fixe
SM, ST, Adv, SM: 0, ST: 1,
Emb Adv: 0, Emb: 0
9673 CMM_TOOL_LOAD_STATION
- Numéro de la station de chargement
SM, ST, Adv, SM: 1, ST: 1,
Emb Adv: 1, Emb: 1
9674 CMM_ENABLE_TOOL_MAGAZINE
- Affichage de la liste de magasin
SM, ST, Adv, SM: 1, ST: 1,
Emb Adv: 1, Emb: 1
9676 CMM_DIRECTORY_SOFTKEY_PATH1
- Chemin des noms de lecteurs dans la gestion de
répertoires
SM, ST, Adv, SM: ", ST: ", Adv:
Emb ", Emb: 0
IM2/4-92
0 47
1 4
0 1
0 4
0 1
0 1
1 2
0 1
*** ***
SINUMERIK 840D sl/840D/840Di/810D MES HMI (IAM) - Édition 08/2005
H01, H02, QV: FBSP,
H05 FBT
BYTE 3/4
IMMEDIA SW4.3 ,
T ST SW6.1
H01, H02, QV: FBSP,
H05 FBT
BYTE 3/4
Power On SW6.1,
ST SW6.1
H01, H02, QV: FBSP,
H05 FBT
BYTE 3/4
Power On SW6.1
H01, H02, QV: FBSP
H05
BYTE 3/4
Power On 840D SW4.3,
810D SW2.3
H01, H02, QV: FBSP,
H05 FBT
BYTE 3/4
Power On 840D SW4.3,
810D SW2.3,
ST SW6.1
H01, H02, QV: FBSP,
H05 FBT
BYTE 3/4
Power On 840D SW4.4,
810D SW2.4,
ST SW6.1
H01, H02, QV: FBSP,
H05 FBT
BYTE 3/4
Power On 840D SW4.4,
810D SW2.4,
ST SW6.1
H01, H02, QV: FBSP,
H05 FBT
BYTE 3/4
Power On 840D SW4.4,
810D SW2.4,
ST SW6.1
H01, H02, QV: FBSP,
H05 FBT
STRING 3/4
Power On 840D SW4.4,
810D SW2.4
mit SM
© Siemens AG 2005 All Rights Reserved
08/2005