EGO AURA-R2 RMR1500E Mode D'emploi page 17

Assemble the Charging Station (Fig. I)
Check GNSS Signal and Secure Charging Station Location
(Fig. J)
1. Make sure the mower in the charging station, the charging
status indicator will flash GREEN or glow solid GREEN.
2. Follow the guidance in the app. Tap Start > Next
3. If the auto-check is successful, you can go ahead and attach the
charging station to the ground with the supplied 6 screws. If not,
you need to relocate the charging station and try again. Follow
the guidance in the app.
4. Fix the low-voltage cable on the ground with stakes.
WARNING: Make sure the low-voltage cables are not placed on the
lawn or anywhere the mower may pass over. Otherwise the cables may
get damaged.
Update to the Latest Firmware
EGO AURA-R2 uses Over-The-Air (OTA) to update the firmware. To fully
experience EGO AURA-R2, prior to use, please update to the latest
firmware in the app.
Tap (Device Details) > Firmware update
It is recommended to turn on the 'Allow auto updates' to ensure the
robotic mower always up-to-date, to deliver the optimal performance.
The mower will complete the update when the following preconditions
are met:
◾
Make sure the mower is switched ON and has paired with the
antenna if you purchase ARA2000.
◾
The mower is in the charging station, make sure proper contacts
between the mower and the charging station.
◾
The battery level of the mower is above 30%.
◾
The mower has stable network connection.
Follow the instructions in the app, and wait for 10-30 min to
automatically complete the firmware update depending on the network
conditions. During this process, please do not switch off or perform
other operations. You can start using it after the app prompts that the
update is successful.
Preparation Before Mapping
Follow the guidance in the app.
Map out the Mowing Zone
Map out the boundary (Fig. K)
A boundary is a virtual line created to define the mower's mowing zone.
If you have more than one lawn or a large lawn that needs to be
divided into several parts, create multiple zones and connect them with
transport paths.
For RMR1500E/RMR3000E, maximum 20 mowing zones can be created
on a map.
For RMR6000E, maximum 40 mowing zones can be created on a map.
1. Make sure the mower is switched ON. With Bluetooth
connection, your smartphone will connect to the mower
automatically.
NOTE: If the mower status is locked, you must enter the PIN code
before operating the mower.
2. Tap Start mapping > Add elements > Boundary.
3. App will calibrate the mower to ensure accurate positioning.
Once complete follow instructions on the app screen to complete
the following steps.
4. Find a proper starting point along the edge of your lawn and use
the app to drive mower to that location. Keep within 6 m of the
mower during the mapping process.
5. Keep a minimum 10 cm from wall/fences and other obstacles
(like trees).
6. Drive the mower around the boundary using the app control
along the edge.
7. Follow the app prompts to save the work area, or create more
map elements. Be sure to save when final map element is
created.
CAUTION: Do not let the product operate on gravel.
Create a No-go Zone (Fig. L)
The no-go zone is an area created within the boundary to restrict the
mower's mowing zone.
To protect both your mower and objects on the lawn, you can set
borders for objects or areas that you don't want the mower to enter.
For example, a flowerbed, a ditch, a hole, lawn decorations, a pond, a
pool, sprinkler heads, or emerged roots. If you have recently installed
a trampoline or grill on the lawn, you can also set it as a no-go zone to
protect it.
Follow the guidance in the app. When you need to cancel the area (like
when you remove the trampoline from the lawn), just delete it via the
app.
A no-go zone can also be used to define a rewilding zone. You can set
up rewilding zones for places where the grass is left to grow naturally,
creating a home for wildlife like bees, butterflies, and hedgehogs.
Tap > Start mapping > Add elements > No-go zone
Create a Transport Path (Fig. M)
A transport path is the passage between two mowing zones, or between
mowing zones and back to the charging station. The mower can operate
automatically in this path, but does not cut grass.
Tap Start mapping > Add elements > Path
NOTE: Path creation must start within a mowing zone and end within a
separate mowing zone or the docking point. Create boundaries for both
zones before creating the transport path to link them.
NOTE: If the charging station docking point is not in the mowing zone,
create a transport path between the mowing zone and the charging
station, refer to the section "Examine where to put the charging
station".
DAILY USE
Mow
How does EGO AURA-R2 mow (Fig. A)
®
Inside the mowing zone, the mower will mow the lawn along a planned
ROBOTIC MOWER — RMR1500E/RMR3000E/RMR6000E
EN
17