ero electronic MKS Manuel De Service page 28

Sñ.LL Servomotor low limit. Servomotor low limit Servomotor low limit Servomotor low limit Servomotor low limit
This parameter is available only when
P5 = Sñ.CL
Range: from 0 (in % of the travel time or of the
feedback potentiometer span) to Sñ.HL.
Sñ.HL Servomotor high limit Servomotor high limit Servomotor high limit Servomotor high limit Servomotor high limit
This parameter is available only when
P5 = Sñ.CL
Range from SñLL to 100 (in % of the travel time
or of the feedback potentiometer span).
Cy1 Output 1 cycle time Output 1 cycle time Output 1 cycle time Output 1 cycle time Output 1 cycle time
This parameter is available only if P5 is equal to
"rEv" or "dir".
Range:From 1 to 200 s.
Cy3 Output 3 cycle time Output 3 cycle time Output 3 cycle time Output 3 cycle time Output 3 cycle time
This parameter is available only if P7 is equal to
"rEv" or "dir".
Range:From 1 to 200 s.
rC Relative Cooling gain. Relative Cooling gain Relative Cooling gain
Relative Cooling gain Relative Cooling gain
This parameter is available only if
configured with two control outputs and
A) Pb is different from 0 or.
B) device is in manual mode
Range: from 0.20 to 1.00
Note: When the device is working with SMART Note Note Note Note
algorithm and P37 is set to ON the rC value is
limited in accordance with the selected type of
cooling media:
- from 0.85 to 1.00 when P25 = AIr
- from 0.80 to 0.90 when P25 = OIL
- from 0.30 to 0.60 when P25 = H2O
OLAP Dead band/Overlap between H/C Dead band/Overlap between H/C Dead band/Overlap between H/C Dead band/Overlap between H/C Dead band/Overlap between H/C
outputs outputs. outputs outputs outputs
This parameter is available only if device is
configured with two control outputs and
A) Pb is different from 0 or.
B) device is in manual mode
Range: from -20 to 50 % of the proportional
band.
A negative OLAP value shows a dead band
while a positive value shows an overlap.
rL Set point low limit Set point low limit Set point low limit Set point low limit Set point low limit
Range: from min. range value (P3) to rH.
Note: When P3 has been modified, rL will be Note Note Note Note
realigned to it.
XKSser1-B0.PMD 22
r H Set point high limit Set point high limit Set point high limit Set point high limit Set point high limit
Range:from rL to full scale value (P4)
Note Note Note: When P4 has been modified, rH will be Note Note
realigned to it.
Grd1 Ramp applied to an increasing set point Ramp applied to an increasing set point Ramp applied to an increasing set point Ramp applied to an increasing set point Ramp applied to an increasing set point
change change change change change
Range: from 1 to 100 digits per minutes.
Above this value the display shows "Inf"
meaning that the transfer will be done as a step
change.
Grd2 Ramp applied to a decreasing set point Ramp applied to a decreasing set point Ramp applied to a decreasing set point Ramp applied to a decreasing set point Ramp applied to a decreasing set point
changes changes changes changes changes
For other details see Grd1 parameter.
OLH Output high limit Output high limit Output high limit Output high limit Output high limit
This parameter is not available when P5 = Sñ.CL
or Sñ.OL .
Range:
- From 0 to 100% when the device is
configured with one control output.
device is - From -100% to 100% when the device is
configured with two control outputs.
tOL Time duration of the output power limiter Time duration of the output power limiter Time duration of the output power limiter
Time duration of the output power limiter Time duration of the output power limiter
This parameter is not available when
P5 = Sñ.CL or Sñ.OL
Range: from 1 to 540 min.Above this value the
display shows "InF" meaning that the limiting
action is always on
Note: The tOL can be modified but the new Note Note Note Note
value will become operative only at the next
instrument start up.
rñP Control output max. rate of rise Control output max. rate of rise Control output max. rate of rise Control output max. rate of rise Control output max. rate of rise
This parameter is available when Pb is different
from zero.
Range: from 0.1 to 25.0 %/s.Above this value
the display shows "InF" meaning that no ramp
limitation is imposed.
Sñ.CA Servomotor control action Servomotor control action Servomotor control action Servomotor control action Servomotor control action
("rEv" for reverse control action and "dir" for
direct control action).
This parameter is available when P5 = Sñ.CL or
P5 = Sñ.OL
Notes: Notes Notes Notes Notes
1) When P24 = nonE or AU.nA, this parameter
can be modified.
2) When P24 = rE.dr, this parameter can be
displayed only.
GB GB GB GB GB 22
12/09/2005, 9.46