Lenze Global Drive 8200 vector Instructions De Montage page 153

Show/Hide Bookmarks
Code
No. Name
C0440 Additional JOG
values
(A)
1 JOG 1
2 JOG 2
3 JOG 3
4 JOG 4
5 JOG 5
6 JOG 6
7 JOG 7
C0469* Function of key
s s
of the keypad of the keypad
C0500* Calibration of
numerator variable
C0501* Calibration of
denominator process
variable
C0500* Calibration of
process variable
(A)
numerator
C0501* Calibration of
denominator process
(A)
variable
C0502* Process variable unit
(A)
C0517* User menu
v
1 Memory 1
2 Memory 2
3 Memory 3
4 Memory 4
5 Memory 5
6 Memory 6
7 Memory 7
8 Memory 8
9 Memory 9
10 Memory 10
C0518 Service codes
C0519
C0520
C0597* Configuration of g
v
motor phase failure
detection detection
C0599* Current limit value
v
for motor phase
failure detection
C0608* Fan monitoring
L
Possible settings
Lenze Selection
20.00 -650.00
30.00
40.00
15.00
25.00
35.00
45.00
s
1 0
1
2
2000 1
10 1
2000 1
10 1
0 0: —
1: ms
2: s
4: A
5: V
50 C0050
34 C0034
7 C0007
10 C0010
11 C0011
12 C0012
13 C0013
15 C0015
16 C0016
2 C0002
0 0
h f il
1
2
5 1
g 0
0
1
2
{0.02 Hz
not active
CINH (controller inhibit)
QSP (quick stop)
{1}
{1}
{1}
{1}
6: rpm 13: % 18: Ω
9: °C 14: kW 19: hex
10: Hz 15: N 34: m
11: kVA 16: mV 35: h
12: Nm 17: mΩ 42: mH
Output frequency (MCTRL1-NOUT)
Analog setpoint selection range
Fixed configuration - digital input signals
Minimum output frequency
Maximum output frequency
Acceleration time main setpoint
Deceleration time main setpoint
V/f rated frequency
V boost
min
Parameter set transfer
not active
TRIP fault message
Warning
{1 %}
not active
TRIP fault message
Warning
EDK82EV903 DE/EN/FR 1.0
Commissioning
Code table
IMPORTANT
JOG = Setpoint
Activation via configuration under C0410
650.00 C04401/1 and C0037 are the same
C04401/2 and C0038 are the same
C04401/3 and C0039 are the same
Determines the function which is activated when
s s
pressing pressing .
Changes will only be active after mains Changes will only be active after mains
switching!
•
The codes C0010, C0011, C0017, C0019,
25000
C0037, C0038, C0039, C0044, C0046,
C0049, C0050, C0051, C0138, C0139,
C0140, C0181, C0239, C0625, C0626, C0140 C0181 C0239 C0625 C0626
25000
C0627 can be calibrated in a way that the
keypad indicates a process variable.
•
If C0500/C0501 remain unchanged, the unit
"Hz" will no longer be displayed.
•
The codes C0037, C0038, C0039, C0044,
25000
C0046, C0049, C0051, C0138, C0139,
C0140, C0181 can be calibrated in a way ,
th t th k that the keypad indicates a process variable d i di t
25000
with the unit selected under C0502.
•
Frequency-related codes (C0010, C0011,
C0017 C0019 C0050 C0239 C0625 C0017, C0019, C0050, C0239, C0625,
C0626, C0627) are always indicated in "Hz".
•
After mains switching or when using the
g
function the code from C0517/1 will be
displayed. displayed
• •
In Lenze setting, the user menu contains the In Lenze setting the user menu contains the
most important codes for setting up the most important codes for setting up the
control mode V/f characteristic control with control mode "V/f characteristic control with
linear characteristic"
•
When the password protection is activated, Wh h d
only the codes entered under C0517 are only the codes entered under C0517 are
freely accessible. freely accessible.
• •
Enter the required code numbers in the Enter the required code numbers in the
subcodes subcodes.
Modifications only by Lenze Service! o o o y y
Keypad: L L L L P P P P 1 1 1 1 , bus: 32
Keypad: L L L L P P P P 1 1 1 1 , bus: 182
•
50 Threshold for C0597
•
Reference: Rated controller current
Function not active at present p
Absolutely set C0608 = 0
y
i bl
i i i d
75