Lenze Global Drive 8200 vector Instructions De Montage page 151

Show/Hide Bookmarks
Code
No. Name
C0421 Free configuration
v v
analog process data g p
output words t t
( (continued) )
C0422* Offset analog output
X3/62
(AOUT1-OFFSET)
Standard I/O
C0422* Offset analog outputs
Application I/O
(A)
1 X3/62
(AOUT1-OFFSET)
2 X3/63
(AOUT2-OFFSET)
C0423* Delay digital outputs
(A)
1 Relay output K1
(RELAY)
2 Digital output X3/A1
(DIGOUT1)
3 Digital output X3/A2
(DIGOUT2)
C0424* Output signal range -
v
analog outputs
Application–I/O
(A)
1 X3/62 (AOUT1)
2 X3/63 (AOUT2)
L
Possible settings
Lenze Selection
Output of analog signals on bus
Analog signal source
d
27 Output frequency without slip (MCTRL1-NOUT)
28 Act. process controller value (PCTRL1-ACT)
29 Process controller setpoint (PCTRL1-SET1)
30 Process controller output without precontrol
(PCTRL1-OUT)
31 Ramp function generator input (NSET1-RFG1-IN)
32 Ramp function generator output (NSET1-NOUT)
33 (A) PID controller output (PCTRL1-PID-OUT)
34 (A) Process controller output (PCTRL1-NOUT)
35 Input signal at X3/8 or X3/1U, X3/1I,
evaluated with gain (C0414/1 or C0027) and offset
(C0413/1 or C0026) (AIN1-OUT)
36 Input signal at frequency input X3/E1,
evaluated with gain (C0426) and offset (C0427)
(DFIN1-OUT)
37 Motor potentiometer output (MPOT1-OUT)
38 Input signal at X3/2U, X3/2I,
evaluated with gain (C0414/2) and offset (C0413/2)
(AIN2-OUT)
40 AIF input word 1 (AIF-IN.W1)
41 AIF input word 2 (AIF-IN.W2)
50 ... 53 CAN-IN1.W1 ... 4 oder FIF-IN.W1 ... FIF-IN.W4
Word 1 (50) ... word 4 (53)
60 ... 63 CAN-IN2.W1 ... 4
Word 1 (60) ... word 4 (63)
255 Not assigned (FIXED-FREE)
0.00 -10.00
0.00
-10.00
0.000
0.000
0.000
0.000
0 0 0 ... 10 V / 0 ... 20 mA
0 1 4 ... 20 mA
{0.01 V}
{0.01 V}
{0.001 s}
EDK82EV903 DE/EN/FR 1.0
Commissioning
Code table
IMPORTANT
24000 ≡ 480 Hz
1000 ≡ Maximum value analog input signal (5 V,
10 V, 20 mA, 10 kHz)
Condition: Gain of analog input or frequency g p
input set to: i t t t
C0414/x, C0426 = 20/C0011 [%]
Setpoint to drive from communication module to
AIF AIF
Normalisation via AIF
Setpoints to controller from CAN or function
module to FIF
Normalisation via CAN or FIF N li i i CAN
10.00 C0422 and C0109 are the same
10.00 C0422/1 and C0109 are the same
65.000 "Debouncing" of digital outputs
( (as of version application-I/O E82ZAFA ... Vx11) pp
•
Switches the digital output if the linked
signal is still active after the time set.
•
Digital output reset with delay Di it l t t t ith d l
Observe the jumper setting of the function
module!
(as of version application-I/O E82ZAFA ... Vx11)
q y
FIF
)
73