Lenze Global Drive 8200 vector Instructions De Montage page 148

Show/Hide Bookmarks
Commissioning
Code table
Code
No. Name
C0418* Free configuration of
v controller status
messages (2)
1 Bit 0
... ...
16 Bit 15
C0419 Free configuration of
v v analog outputs analog outputs
1 X3/62 (AOUT1-IN)
2 (A) X3/63 (AOUT2-IN)
3 (A) X3/A4 (DFOUT1-IN)
70
Possible settings
Lenze Selection
Output of digital signals to bus
255 Digital signal sources like C0415
255
Analog signal output to terminal
Analog signal source
0 0 Output frequency (MCTRL1-NOUT+SLIP)
2 1 Device utilisation (MCTRL1-MOUT) under C0014 = 2
or 3
Motor torque (MCTRL1-MACT) under C0014 = 4
3 2 Apparent motor current (MCTRL1-IMOT)
3 DC-bus voltage (MCTRL1-DCVOLT)
4 Motor power
5 Motor voltage (MCTRL1-VOLT)
6 1/output frequency (1/C0050) (MCTRL1-1/NOUT)
7 Output frequency with limits (NSET1-C0010...C0011)
8
Operation with process controller (C0238 = 0, 1):
Act. process controller value (PCTRL1-ACT)
Operation without process controller (C0238 = 2):
Output frequency without slip (MCTRL1-NOUT)
9 Ready for operation (DCTRL1-RDY)
10 TRIP fault message (DCTRL1-TRIP)
11 Motor is running (DCTRL1-RUN)
12 Motor is running / CW rotation (DCTRL1-RUN-CW)
13 Motor is running / CCW rotation (DCTRL1-RUN-CCW)
14 Output frequency = 0 (DCTRL1-NOUT=0)
15 Frequency setpoint reached (DCTRL1-RFG1=NOUT)
16 Q threshold reached (PCTRL1-QMIN)
min
17 I limit reached (MCTRL1-IMAX)
max
C0014 = -5-: Torque setpoint reached
18 Overtemperature (ϑ
19 TRIP or Q or pulse inhibit (IMP) active
min
(DCTRL1-TRIP-QMIN-IMP)
20 PTC warning (DCTRL1-PTC-WARN)
21 Apparent motor current < current threshold
(DCTRL1-IMOT<ILIM)
22 Apparent motor current < current threshold and Q
threshold reached (DCTRL1-(IMOT<ILIM)-QMIN)
23 Apparent motor current < current threshold and RFG
1: Input = output (DCTRL1-(IMOT<ILIM)-RFG-I=0)
24 Warning motor phase failure (DCTRL1-LP1-WARN)
25 Minimum output frequency reached (PCTRL1-NMIN)
EDK82EV903 DE/EN/FR 1.0
IMPORTANT
•
• •
•
•
6 V/12 mA/5.85 kHz ≡ C0011
3 V/6 mA/2.925 kHz ≡ Rated motor torque with
vector control (C0014 = 4), otherwise rated
active inverter current (active current/C0091)
3 V/6 mA/2.925 kHz ≡ Rated inverter current
6 V/12 mA/5.85 kHz ≡ DC 1000 V (400 V- mains
6 V/12 mA/5.85 kHz ≡ DC 380 V (230 V mains)
3 V/6 mA/2.925 kHz ≡ Rated motor power
4.8 V/9.6 mA/4.68 kHz ≡ Rated motor voltage
2 V/4 mA/1.95 kHz ≡ 0.5 × C0011
0 V/0 mA/4 mA/0 kHz ≡ f = f
6 V/12 mA/5.85 kHz ≡ f = f
6 V/12 mA/5.85 kHz ≡ C0011
Selection 9 ... 25 correspond to the digital
functions of the relay output K1 (C0008) or the f
digital output A1 (C0117): digital output A1 (C0117):
LOW = 0 V/0 mA/4 mA/ 0 kHz LOW = 0 V/0 mA/4 mA/ 0 kHz
HIGH = 10 V/20 mA/10 kHz HIGH = 10 V/20 mA/10 kHz
- 5 °C) (DCTRL1-OH-WARN)
max
Belt monitoring
Apparent motor current = C0054 pp
Current threshold = C0156
min
The assignment is mapped to the
– Controller status word 2 (C0151)
– FIF output word 2 (FIF-OUT.W2) FIF output word 2 (FIF OUT.W2)
– Output word 1 in the CAN object 2 p j
(CAN OUT2 W1) (CAN-OUT2.W1)
All bits can be freely configured All bits can be freely configured
The selection made under C0111 is
copied to C0419/1. A change of C0419/1 copied to C0419/1. A change of C0419/1
sets C0111 = 255!
DFOUT1: 50 ... 10 kHz
(C0010)
min
(C0011)
max
p g
i f h l K1 (C0008)
L
h