Lenze Global Drive 8200 vector Instructions De Montage page 127

Show/Hide Bookmarks
Code
No. Name
C0008 Fixed configuration of
v
relay output K1
(relay) ( y)
C0009* Controller address
v
C0010 Minimum output
frequency
u u u u S S S S E E E E r r r r
C0011 Maximum output
frequency
u u u u S S S S E E E E r r r r
C0012 Acceleration time
main setpoint
u u u u S S S S E E E E r r r r
C0013 Deceleration time
main setpoint
u u u u S S S S E E E E r r r r
C0014 Operating mode p
v
L
Possible settings
Lenze Selection
1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
255
1 1
0.00 0.00
14.5 Hz
à
50.00 7.50
87 Hz
à
5.00 0.00
5.00 0.00
g 2
2
3
4
5
Ready for operation (DCTRL1-RDY)
TRIP fault message (DCTRL1-TRIP)
Motor is running (DCTRL1-RUN)
Motor is running / CW rotation (DCTRL1-RUN-CW)
Motor is running / CCW rotation (DCTRL1-RUN-CCW)
Output frequency = 0 (DCTRL1-NOUT=0)
Frequency setpoint reached (MCTRL-RFG1=NOUT)
Frequency threshold Q reached (PCTRL1-QMIN)
min
I limit reached (MCTRL1-IMAX)
max
C0014 = 5: Torque setpoint reached
Overtemperature (J -5 °C) (DCTRL1-OH-WARN)
max
TRIP or Q or pulse inhibit (IMP) (DCTRL1-IMP)
min
PTC warning (DCTRL1-PTC-WARN)
Apparent motor current < current threshold
(DCTRL1-IMOT<ILIM)
Apparent motor current < current threshold and Q
threshold reached (DCTRL1-(IMOT<ILIM)-QMIN)
Apparent motor current < current threshold and RFG
1: Input = output (DCTRL1-(IMOT<ILIM)-RFG1=0)
Warning motor phase failure (DCTRL1-LP1-WARN)
Minimum output frequency reached (PCTRL1-NMIN)
Free configuration under C0415/1
{1}
{0.02 Hz}
{0.02 Hz}
{0.02 s}
{0.02 s}
V/f characteristic control V ~ f
2
V/f characteristic control V ~ f
Vector control
Sensorless torque control with speed limitation
•
Torque setpoint via C0412/6
•
Speed limitation via setpoint 1 (NSET1-N1), if
C0412/1 is assigned, if not via max. frequency
(C0011)
EDK82EV903 DE/EN/FR 1.0
Commissioning
Code table
IMPORTANT
Change under C0008 will be copied to
C0415/1. Free configuration under C0415/1
sets C0008 = 255!
Belt monitoring
Apparent motor current = C0054 pp
Current threshold = C0156
min
Only display
Do not change C0008 since settings under
C0415/1 can be lost
99 For communcation module to AIF only:
•
LECOM-A (RS232)
•
LECOM-A/B/LI 2102
•
PROFIBUS-DP 213x,
•
System bus (CAN) 217x
•
C0010 is not effective with bipolar setpoint
650.00
selection (-10 V ... + 10 V)
•
C0010 does not have an effect on the
terminals 2U/2I of the application I/O (AIN2) terminals 2U/2I of the application I/O (AIN2)
650.00
Speed setting range 1 : 6 for Lenze
à
geared motors: Setting absolutely required
for operation with Lenze geared motors.
1300.00 Reference: frequency change 0 Hz ... C0011
•
Additional setpoint ðC0220
•
Acceleration times can be activated Über
Digitalsignale aktivierbare Hochlaufzeiten ð
C0101
1300.00 Reference: frequency change C0011 ... 0 Hz
•
Additional setpoint ð C0221
•
Deceleration times to be activated via digital
signals ð C0103
Linear characteristic with constant V
Square-law characteristic with constant V
boost
For initial selection enter the motor data o o
and identify the motor parameters with d id if h
C0148
Otherwise, commissioning is not possible.
boost
min
min
o o
i h
49