Lenze Global Drive 8200 vector Instructions De Montage page 128

Show/Hide Bookmarks
Commissioning
Code table
Code
No. Name
C0015 V/f rated frequency
u u u u S S S S E E E E r r r r
C0016 V boost
min
u u u u S S S S E E E E r r r r
C0017 Frequency threshold
Q
min
C0018 Chopper frequency pp q y
v
C0019 Operating threshold
for automatic
DC-injection brake
(Auto-DCB)
C0021 Slip compensation
C0022 I limit (motor
max
mode)
C0023 I -limit in the
max
generator mode
C0026* Offset analog input 1
(AIN1–OFFSET)
C0027* Gain analog input 1
(AIN1-GAIN)
C0034* Setpoint selection
range g
v S Standard–I/O (X3/8) d d I/O (X3/8)
u u u u S S S S E E E E r r r r
C0034* Setpoint selection
v
range
Application- I/O
(A)
u u u u S S S S E E E E r r r r
1 X3/1U, X3/1I
2 X3/2U, X3/2I
C0035* DC injection brake j
v
(DCB) control mode (DCB) l d
50
Possible settings
Lenze Selection
50.00 7.50
à 0.00
0.00 0.00
6 0 2 kHz sin
1 4 kHz sin
2 8 kHz sin
3 16 kHz sin
4 2 kHz f_top
5 4 kHz f_top
6 8 kHz f_top
7 16 kHz f_top
8 1 kHz sin
Reserved
9 ... 11
12 1 kHz f_top
0.10 0.00
= not active
0.0 -50.0
150 30
150 30
0.0 -200.0
100.0 -1500.0
0
0 0 ... 5 V / 0 ... 10 V / 0 ... 20 mA
1 4 ... 20 mA
2 -10 V ... +10 V
3 4 ... 20 mA Open-circuit monitoring
0
0 Unipolar voltage 0 ... 5 V / 0 ... 10 V
1 Voltage bipolar -10 V ... +10 V
2 Current 0 ... 20 mA
3 Current 4 ... 20 mA
4 Current 4 ... 20 mA open-circuit monitored
0
0 Brake voltage selection under C0036
1 Brake current selection under C0036
EDK82EV903 DE/EN/FR 1.0
{0.02 Hz} 960.00 Setting applies to all mains voltages permitted
{0.01 %} 40.00
{0.02 Hz} 650.00 Programmable frequency threshold
low noise generation low noise generation
low power loss low power loss
low power loss
650.00 Holding time ð C0106
{0.02 Hz}
{0.1 %} 50.0
{1 %} 150 After controller enable, 180% I
{1 %} 150 C0023 = 30 %: function is inactive, if
{0.1 %} 200.0
{0.1 %} 1500.0
IMPORTANT
Depending on the controller
à
Setting applies to all mains voltages permitted
•
Reference: Setpoint
•
Signal output configuration under C0415
General rule:
The lower the chopper frequency
•
th l the lower the power loss th l
• •
the higher the noise generation the higher the noise generation
• •
the better the smooth running quality the better the smooth running quality
Medium-frequency motors are only allowed Medium-frequency motors are only allowed
to be operated at 8 kHz sin or 16 kHz sin to be operated at 8 kHz sin or 16 kHz sin
(C0018 = 2 or 3)! ( )
Deactivate the automatic DC injection brake
when the minimum frequency limit C0239 is
active
are available for
r
max. 3 s at C0022 = 150 %
C0014 = 2, 3:
•
Settings for X3/8 and X3/1U, X3/1I
•
The max. limit of the setpoint value range of
C0034 equals 100 %
•
C0026 and C0413/1 are identical
•
Settings for X3/8 and X3/1U, X3/1I
•
100.0 % = Gain 1
•
Inverse setpoint selection by negative gain
and negative offset
•
C0027 and C0414/1 are identical
Observe the switch position of the function
module!
•
Minimum output frequency (C0010) not
effective
•
Individual adjustment of offset and gain
TRIP Sd5, if I < 4 mA
Observe the jumper setting of the function
module!
Minimum output frequency (C0010) not effective
TRIP Sd5 if I < 4 mA
Holding time ð C0107 g
L