The Functions Of The Breadmaker - Unold 8695 Notice D'utilisation

The default program is the same as for the BASIC program.
Phase Preset
Total time 3:10 hours
Knead 1 12 minutes
Rise 1 18 minutes
Knead 2 15 minutes
Rise 2 85 minutes
Rise 3 OFF/AUS
Bake 60 minutes
Keep warm 60 minutes
The times can be programmed as shown in the table.
Proceed as follows:
Select the USER PROGRAM with the Menu button.
Select the desired phase with the ABSCHNITT button.
Knead 1 and the programmed time 0:12 for this phase
appear on the display.

THE FUNCTIONS OF THE BREADMAKER

Alarm function
The alarm sounds:
ƒ whenever an active button is pressed,
ƒ during the second kneading process, to remind you
to add seeds, fruit, nuts or other ingredients. Please
note that this function cannot be deactivated, e.g. in
the time preset function,
ƒ at the end of the baking process, the appliance beeps
often during the keep-warm phase,
ƒ at the end of the keep-warm phase 10 beeps remind
you that the appliance is now switched off and the
bread has to be taken out of the bread pan. Please
note that this function cannot be deactivated, e.g. in
the time preset function.
Repeat function after power outage
Should the electricity supply been cut off during the ope-
ration of the Breadmaker, the appliance will re-start, on
re-instatement of the supply, automatically from the point
arrived at when the cut-off occurred as long as the inter-
ruption is not longer than 2 minutes. If the interruption in
the electricity supply lasts more than 2 minutes and the
display shows the basic setting, the Breadmaker must be
re-started. This is only practical if the dough was not fur-
ther than the kneading phase when the break occurred. If
Programmable time frame
0-14 minutes
0-100 minutes
0-15 minutes
0-100 minutes
0-120 minutes
0-70 minutes
OFF/60 minutes
The time can be changed by means of the ZEITWAHL but-
ton. Press it repeatedly until the desired time appears on
the display (past OFF, if necessary).
Confirm the change with the ABSCHNITT button. Press
this button again and the next program phase and the pro-
grammed time will appear on the display: Rise 1 = and
0:18.
If the maximum programmable time for the respective pro-
gram phase is exceeded by pressing the ZEITWAHL button,
O will appear on the display if this is possible according
to the above table. This phase is then skipped during the
program.
Every programmed setting must be confirmed by pressing
the ABSCHNITT button, so you can continue programming
the next program phase.
Once you have programmed all phases to suit your pre-
ferences, conclude the programming by pressing the AB-
SCHNITT button and then the START/STOP button. The
programmed time for the user program appears on the dis-
play. The program then starts either immediately or after
the time set via the timer function.
the program was already in the last rising cycle when the
power broke down and the interruption lasts over a longer
time, the dough cannot be saved and the program has to
be started again.
Safety functions
The lid should not be opened after the program has star-
ted, except during the second kneading phase for adding
of ingredients. During the rising and baking phase the lid
should never be opened, as the bread may sink down.
If the temperature in the appliance, due to previous use, is
too high (above 40 °C) for a newly chosen program, when
an attempt to restart is made, the display will show H:HH
and an alarm sound will be heard. Should this occur, remo-
ve the pan and wait until the appliance has cooled off and
is back to the beginning of the originally chosen program.
Please not that the breadmaker has no top heating for sa-
fety reasons, so the crust will be lighter on top and darker
at the sides and bottom of the bread. For safety reasons an
additional top heating is not allowed.
If after pressing START/STOP, E:EE is shown in the display,
the temperature control is defective. In this case please
send the appliance to our technical service.
35