Maintenance And Cleaning - ATIKA KGSZ 250 N Notice Originale

Double mitre cuts
Increased danger of injury exists with the double mitre
cut because of the saw blade being more accessible
due to its heavy incline. Keep your hands far enough
away.
1. Loosen the locking screw (7) for the rotary table (8), press
the locking lever (7A) and turn the rotary table clockwisely or
counterclockwisely up to the desired angle.
2. Firmly tighten the locking screw again
3. Loosen the incline angle locking knob (25) and incline the
saw head up to the desired angle to the left.
4. Retighten the incline angle locking knob.
5. Cut the work piece as described under "Straight cuts".
Setting the groove depth
This function allows you to cut grooves into the work piece. The
work piece is only cut to a certain (set) depth and is not cut
through.
Groove cutting poses an increased risk of injury since
the saw head may bounce upward. Do not exert any
lateral pressure on the saw blade. Firmly secure the
work piece with the vise assembly (20).
1. Set the saw head and rotary table to the desired position and
lock it in place.
2. To finely adjust the groove depth loosen the locking nut (33)
for the set screw (32).
The saw head rises when you turn the set screw (32)
counterclockwisely → deeper groove.
The saw head lowers when you turn the set screw (32)
clockwisely → more shallow groove.
3. Retighten the locking nut (33) for the set screw (32).
4. Firmly secure the work piece with the vice assembly (20).
The groove is cut over the whole length if you place a
stop attachment between work piece and work piece stop.
5. Cut the work piece as described under "Straight cuts".

Maintenance and cleaning

Before each maintenance and cleaning work
− switch off device
− Wait for standstill of the saw blade
− pull out power plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or
companies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Cleaning
Observe the following to maintain the functionality of the
saw.
All manuals and user guides at all-guides.com
Maintenance
1. Secure the pulling mechanism.
2. Place the saw head to the top position.
3.
4.
5.
6.
7. Slowly turn the saw blade by hand until the saw blade
8.
9.
10. Position the rear saw blade flange again.
11. Insert a new saw blade.
12. Position the front saw blade flange again.
13. The further assembly is now done in reverse sequence.
14. Check the pendulum cover for its correct functioning before
22
Do not wash down device with water.
Remove splints and sawdust only with a brush or vacuum
cleaner.
Clean and oil all moving parts regularly.
Never use any grease!
Use for instance sewing machine oil, liquid hydraulic
fluid or environmentally acceptable spray oil.
Take care that the saw blade remains free of rust and resin.
Remove resin residues from the surface of the rotary table.
Resin residues can be removed with a commercial
maintenance and care spray.
The saw blade is a wearing part and will become dull after
prolonged or frequent use.
Replace the saw blade in that case.
Thoroughly shake out the dust bag. Wash the dust bag in
case of heavy soiling but at least once a year with a mild
soap solution.
Changing the saw blade
Danger of cutting! Wear gloves when replacing the saw
blade.
Use only suitable saw blades.
Danger of burning! The saw blade is still hot shortly after
cutting.
Loosen the screw (A).
Loosen the screw (B).
Swing the holding plate for the pendulum cover (16A)
down and the pendulum cover (16) up.
Push the saw blade locking device (38).
locking device catches. Keep the saw blade locking device
pressed.
Unscrew the hexagonal screw (34) for the saw blade
( left-handed thread) using the supplied tool (41).
/ Now, the front saw blade flange (35), the saw
blade (36) and the rear saw blade flange (37) can be
removed.
Clean the saw blade flanges.
Pay attention to the correct running direction of the saw
blade: The arrow on the saw blade and the arrow on
the protective cover must point in the same direction!
Retighten the hexagon screw.
proceeding.