Working Instructions; Maintenance And Cleaning; Changing The Saw Blade; Replacing The Wood Insert - ATIKA BWS 500 Notice Originale

Before making adjustments to the saw settings (e.g. replacing the saw
blade etc.)
− switch off device
− wait for standstill of the saw blade.
− pull out power plug
Also, note the following important points:
Place yourself outside of the area of danger.
Place the wood piece in the jigging device. Cut through the piece with
uniform pressure.
Never remove loose splinters, chips, or similar by hand.
At any case pay attention to all safety instructions.

Working instructions

1. Secure the saw against rolling away.
2. Place the wood piece in the jigging device.
Only wood pieces with a max. diameter of 18 cm are allowed to be
sawed.
Pull out the support extension (24) to the desired length and fix it
using the machine knob (25).
You will get pieces of equal length if you pull out the length stop
(30) and fix it in the desired position using the machine knob.
3. Hold the handle (26) on the jigging device with both hands and push the
jigging device uniformly towards the saw blade.
movements.
The barbs on the jigging device prevent any turning of the wood
piece during sawing.
Do not force the jigging device against the saw blade, the motor
speed should not drop too far.
4. After cutting, the jigging device is automatically brought back to its home
position by spring force.
In the home position, all of the saw blade (incl. cutting teeth) is
covered by the saw blade cover (10).
If the recuperating spring (20) is broken or worn, the jigging
device will not automatically return to its home position. Replace the
recuperating spring.
Never saw without or with a damaged recuperating spring.
5. Only advance the wood piece after a completed sawing operation.

Maintenance and cleaning

Before each maintenance and cleaning work
− Switch off device
− Wait unitl the saw blade comes to a stop.
− Pull out power plug
Maintenance and repair work other than those described in this chapter is
only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must unconditionally
be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected damages and
injuries.
Cleaning
Observe the following to maintain the operability of the machine:
Do not wash down device with water.
Remove shavings and dust only with a brush or vacuum cleaner.
13
Clean and oil all moving parts regularly (e.g. safety guard hinge (h)
jigging device hinge (i)
environmentally acceptable spray oil.
Take care that the saw blade remain free of rust and resin.
Remove resin residues from the push frame surface.
Resin residues can be removed with a commercial maintenance and care
spray.
The saw blade is a wearing part and will become dull after prolonged or
frequent use.
Maintenance

Changing the saw blade

Danger of cutting! The saw blade is massive and it could be to slick.
Wear gloves when replacing the saw blade.
Do not use any saw blades made of HSS steel.
Avoid erratic
Do not use any cracked saw blades or such that have changed their
shape.
Only use well-sharpened saw blades.
Danger of burning! The saw blade is still hot shortly after cutting.
1. Remove the saw blade cover (10). (Remove 4 screws.)
2. Fold up the safety guard (11). Insert a wood wedge through the opening (g)
to prevent the guard from hinging down.
3. Remove the clamping screw (16).
4. Now, the front saw blade flange (13) and the saw blade (14) can be
removed.
5. Clean the saw blade flanges (13, 12).
6. Install a new or sharpened saw blade.
Pay attention to the correct running direction of the saw blade: The
arrow on the saw blade and the arrow on the protective cover must point in
the same direction!
7. Position the front saw blade flange again.
8. The further assembly is now done in reverse sequence.
9. Check that the saw blade cover (10) is properly secured.

Replacing the wood insert

Immediately replace a worn or damaged wood insert.
1. Loosen the screws of the wood insert (27) and remove them
2. Insert a new wood insert and screw it tightly in place.

Replacing the recuperating spring

Immediately replace a worn or damaged recuperationg spring.
1. Remove one end of the safety chain (21)
2. Remove the cotter pin (8) and pull out the bolt (19) from the bracket
3. Remove the recuperating spring (20).
4. Slide a new recuperating spring on the bolt.
5. The further assembly is now done in reverse sequence.
W
and recuperating bolt (19)
Never use any grease!
Use for instance sewing machine oil, liquid hydraulic fluid or
Renew the saw blade or have it sharpened
Remove the mains plug before changing the saw
blade.
.I.
L
O
)
.
H – .I.
L
.I.
X
.
R.
O.O
,