Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Clamping of saw chain
Place the power pruner on an even surface as shown.
Loosen the retaining screw (3) by max. 1 turn.
Slightly lift the guide bar tip and turn the chain stretching
screw (21) clockwise until the correct chain tension is
reached.
The saw chain is correctly stretched when it can be lifted
in the centre of the chain guide by appr. 3 – 4 mm.
Turn the chain stretching screw (21) anti-clockwise when
the saw chain is stretched too much.
Check that the chain links are positioned correctly in the
guiding groove of the guide bar.
Tighten the retaining screw (3) again.
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to
the relevant and properly earthed plug.
Use a shockproof plug, mains voltage 230 V with
residual current circuit breaker (FI switch 30 mA).
Only use extension cables with sufficient core cross-section.
Mains fuse
10 A inert
Mounting of the extension cable
Plug the female connector of the extension cable on the
male connector of the device.
Thread the extension cable through the pull relief device
(10) as a loop and hang it up.
Make sure that the extension cable has sufficient play
and is routed toward the rear away from the power
pruner, outside of the range of the saw chain and
material to be sawed.
Wearing the shoulder belt
Place the belt over the shoulder and adjust the belt
length so that the belt attachment (A) is positioned at hip
level. The quick acting closure (14) is located at the
front.
The quick acting closure can be opened with the left hand.
Setting the working height
Loosen the clamping screw (6); you can then pull the two
telescope rods (5, 7) apart or push them together.
Switching on / off
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Securely support the power pruner when switching it on and
hold it with both hands. Chain and guide bar must stand free.
All manuals and user guides at all-guides.com
Switching on
Push and hold automatic trip switch (8). Then operate
the On/Off switch (9). Now, you can release the throttle
automatic trip switch.
Switching off
Release On/Off switch.
Vibrations
If persons who have blood circulation problems are too
often exposed to vibrations damages to the nervous system or
to blood vessels may occur.
You can reduce vibrations:
- by thick and warm working gloves,
- shorter working time (have longer breaks).
See a doctor if your fingers swell, you don't feel well or your
fingers become numb.
W
o
r
k
i
n
g
w
i
t
h
W
o
r
k
i
n
g
w
i
t
h
Saw backstroke
What is saw backstroke? Saw backstroke is the sudden strike
upwards or backwards of the running power pruner in direction
of the operator.
This happens when
− the guide bar tip gets in contact with the sawing material
(unintended) or other hard objects.
− the saw chain is jammed at the guide bar tip.
The power pruner reacts uncontrolled and frequently causes
heavy injuries of the operator.
How to avoid saw backstroke?
− For better control saw with the lower edge of the guide bar.
Place the power pruner as horizontally as possible when
contacting wood.
− Never saw with the guide bar tip.
− Sawing with the upper guide bar edge may cause a saw
backstroke if the saw gets jammed or hits a hard object in
the wood.
− Start cutting only with running saw chain.
− Never switch on the machine with the saw chain put on.
− Always hold the power pruner firmly with both hands.
− Only work with correctly sharpened and clamped saw chain.
General conduct when pruning
Take into consideration environmental influences:
− Do not work on snow, ice or recently peeled wood – slip
hazard.
− Do not work under insufficient light conditions (e.g. fog,
rain, snow flurry or twilight). You can not see anymore
details within the falling area – risk of accident.
Delay the work in case of disadvantageous weather
−
(rain, snow, ice, wind) – increased risk of accidents!
t
h
e
p
o
w
e
r
p
r
u
n
e
r
t
h
e
p
o
w
e
r
p
r
u
n
e
r
15
Publicité
Chapitres
Table des Matières
