Before The First Start-Up; Start-Up; Mains Connection; On/Off Switch - ATIKA BWS 500 Notice Originale

K
J -
Insert the adjusting screw (17) with one washer through the saw
blade cover (9). Install another washer and the hexagon nut (f) (do
not yet tighten). Screw the screw (17) into the threaded hole of the
device unit (1). The adjusting screw (17) can be used to align the
saw blade cover (9) with the saw blade (14).
The saw blade cover must be parallel to the saw blade. Then,
secure with the lock nut (f).
L
Install the saw blade cover (10).
Assembling the jigging device
M
Install the jigging device (18) on the assembled device unit. Tighten
the screws on the jigging device only by hand and then slacken the
nuts by a half turn. The jigging device must move freely.
Installing the recuperating bolt
N - O
Install the recuperating bolt (19) with the recuperating spring (20) on
the bracket (c). Insert the recuperating bolt through into the hole of the
bracket (d).
The recuperating spring (20) must rest on the bracket.
Fix the bolt using the securing cotter pin (8).
Transport locking device and safety chain
P
Insert the screw [M8x55] and washer into the upper hole of the
jigging device (18) and secure it using a washer and a nut.
Q
Screw the machine knob (22) on the end of the tread. Insert the
screw [M8x45] with washer and safety chain (21) into the bottom
hole of the jigging device. Secure these parts with one washer and a
self-locking nut.
R – S
Place the transport locking device (23) on the screw and secure it
using the lock nut as shown in figure
Do not over tighten the lock nut. The transport safety device
must move freely.
Insert the screw into the bracket (e) of the frame and place the end of
the safety chain (21) on the screw end. Fix the safety chain using a
nut.
Assembling the support extension
U
Insert the support extension (24) and secure it with the machine knob
(25).
Assembling the length stop
Insert the length stop (30) into the jigging device. Secure the length stop with
the star grip knob (25).
Assembling the handle
V
Install the handle (26) using 2 screws [M8x15] and washers.

Before the first start-up

To achieve flawless functioning of the machine, please follow the
instructions listed:
Place the saw at a location which meets following conditions:
− outdoor
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
To ensure a safer foothold when working with the saw secure the saw
against rolling away.
Before each use, check
− connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
R.
− that the wood insert is in a proper condition
− the saw blade for flawless condition
− the functioning of the jigging device
Do not use any cracked saw blades or such that have changed their
shape.
Do not use any saw blades made of HSS steel.
Immediately replace a worn or damaged wood insert.
Assume the correct work posture. Stand in front of the operating side
frontally to the saw blade line.

Start-up

Rotational direction of the saw blade
Ensure that the rotational direction of the saw blade is the same as the
rotational direction given on the guard (11)
Selection of saw blades
Consider when selecting the saw blade, that no edgeless or damaged saw
bands are used and that the diameter of the blade location hole is 30 mm
(note the nameplate on the machine).

Mains connection

Compare the voltage given on the machine model plate e.g. 230 V with the
mains voltage and connect the machine to the relevant and properly earthed
plug.
Use a shockproof plug, mains voltage 230 V with residual current circuit
breaker (FI switch 30 mA).
Main fuse: 16 A inert

On/Off switch

Do not use any device where the switch can not be switched on and off.
Damaged switches must be repaired or replaced immediately by the
customer service.
Characteristic data of noise
Press the green button ( I ) on the switch.
If there is a power cut, the machine switches
off automatically. Push the green ( I ) button
to start the machine again.

Switching off

Press the red button (O) or the red button of the yellow switch
cover. The built-in motor brake will decelerate the saw blade up to
the dead stop within 10 seconds.
The saw must not be used if the brake is defective, i.e. if the time
up to the saw blade's dead stop exceeds 10 seconds.

Working with the saw

Before starting to work consider the following safety advices to keep the
risk of injuries as small as possible.
Saw blade, wood insert, recuperating spring o. k.
Workplace tidied?
You may not start to operate the machine until you have read these
operating instructions, observed all the instructions given and installed
the machine as described!
.
12