Adjusting The Saw - ATIKA KGSZ 305 N Notice Originale

Make sure that the connections for the dust extraction
and the dust bag (collecting device) are connected and
used correctly.
Dust bag

When using the dust bag:

 push the dust bag (23) onto the exhaust neck (24).
 regularly empty the dust bag.
Chip exhaustion
Connect a chip exhaust system or small vacuum cleaner
with suitable adapter to the chip exhaust neck (24) (dia. 44
mm).

Air velocity at the exhaust neck of the saw ≥ 20 m/sec.
Use a special exhaust device when exhausting dusts that
are especially harmful to health, carcinogen or dry.
Attaching table extensions
Handling long work pieces with the help of the
supplied support arms.
The support arms can be mounted to the left and right of
the machine.

 Insert the support arms (18) into the respective holes
on the sides.

Secure the support arms using the machine knobs
(19).

Safely support long work pieces with suitable means. For
example, use saw horses or similar devices to support
overhanging work pieces.
Vice assembly
Always secure work pieces to be handled. Do not cut
work pieces that cannot be secured with the vice
assembly.
The vice assembly can be positioned to the left or right of
the saw head.

 Insert the vice assembly (20) at the right or left into the hole
provided.
 Secure it using the machine knob (21A).
 Press the work piece firmly against the work piece stop (11).
 To fix the work piece turn the machine knob (22) of the work
piece clamping device clockwisely.

Adjusting the saw

Before setting operations:
 switch off device
 wait for standstill of the saw blade
 pull out power plug

1. If required, loosen the incline angle locking knob (25) and
adjust the saw head to its vertical position.
2. Retighten the incline angle locking knob.
3. Push the saw head to the rear and tighten the locking screw
of the pulling device (6).
4. Loosen the locking screw (7) for the rotary table (8), pull the
locking (7A) out and turn the saw head to the 0° position.
5. Firmly tighten the locking screw again
6. Press the saw head down (transport position) and
secure it using the transport locking pin (5).
Setting the work piece stop

To adjust a work piece stop that has shifted during
transport, proceed as follows:

1. Check the angle between saw blade (36) and work piece
stop (11) using a square (A, not supplied).
2. Loosen the set screws (2 on each side) for the work piece
stop (12) if the work piece stop needs to be adjusted
3. Align the work piece stop along the square and tighten the
locking screw again.
Adjusting the incline of the saw head

Also check the angle of the saw head to the rotary table.
Checking the 90° angle:
 Check the angle using a square (A, not supplied).
Proceed as follows if the angle is not exactly 90°:

 Loosen the locking nut (29) for the set screw (28).
 Loosen the incline angle locking knob (25).
 Adjust the set screw (28) by turning it clockwisely or
counterclockwisely so that the saw blade comes in contact
with the square (90°).
 Retighten the locking nut (29) for the set screw (28).

If necessary, loosen the screw for the indicator (27) and
shift it until it points to "0". Tighten the screw again.
Checking the 45° angle:
Incline the saw head by 45° to the left and check the

angle using a protractor (B, not supplied).
Proceed as follows if the angle is not exactly 45°:
 Loosen the locking nut (31) for the set screw (30).
 Loosen the incline angle locking knob (25).
 Adjust the set screw (30) by turning it clockwisely or
counterclockwisely so that the saw blade comes in contact
with the protractor ( 45°).
 Retighten the locking nut (31) for the set screw (28).
21