Commissioning; Switching Off; Dust/Chip Exhaustion; Adjusting The Saw - ATIKA KGSZ 305 Notice Originale

To ensure a safe position of the saw it must be bolted down
on a solid surface (e.g. workbench or support frame) at opti-
mal working height:
− Disengage the transport locking pin
−
Make 4 holes in the support matching the holes in the
base plate (43).
− Bolt the device down.
Before each use, check
− Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
− the saw blade for flawless condition
Do not use deformed or damaged saw blades.
Immediately replace a worn or damaged table insert.
Connect the mitre crosscut saw to a dust collection device
when cutting wood.

Commissioning

Mains connection
Compare the voltage listed on the device type plate, e.g. 230 V,
with the mains voltage and connect the device to the corre-
sponding and proper socket.
Connect the machine via a 30 mA fault-current circuit breaker.
Use the connection or extension cable according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm for cable lengths up to 25 m
2
2.5 mm for cable lengths over 25 m
2
On / Off Switch
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired or
replaced immediately by the customer service.
Switch on
Activate the On/Off switch (1).

Switching off

Release the On/Off switch again.

Dust/chip exhaustion

The wood dust generated during operation impedes the
necessary view and is harmful to health to some degree.
Unless the machine is used outdoors, the dust bag (23) or a
chip exhaust system (e.g. portable dust remover) must be con-
nected.
Dust bag
When using the dust bag:
push the dust bag (23) onto the exhaust neck (24).
regularly empty the dust bag
Chip exhaustion
Connect a chip exhaust system or small vacuum cleaner
with suitable adapter to the chip exhaust neck (24) (dia. 37 mm).
Air velocity at the exhaust neck of the saw ≥ 20 m/sec
Use a special exhaust device when exhausting dusts that are
especially harmful to health, carcinogen or dry.
Attaching table extensions
Handling long work pieces with the help of the supplied
support arms.
The support arms can be mounted to the left and right of the
machine.
- Insert the support arms (18) into the respective holes on the
sides.
- Secure the support arms with the wing screws (19).
Safely support long work pieces with suitable means. For exam-
ple, use saw horses or similar devices to support overhanging
work pieces.
Vice assembly
Always secure work pieces to be handled. Do not cut
work pieces that cannot be secured with the vice assembly.
The vice assembly can be positioned to the left or right of
the saw head.
- Insert the vice assembly (20) at the right or left into the hole
provided.
- Secure it with the wing screws (21).
- Press the work piece firmly against the work piece stop (11).
- Turn the machine knob of the vice assembly clockwise.

Adjusting the saw

Pull the mains plug before performing set-
tings.
Setting the work piece stop
To adjust a work piece stop that has shifted during
transport, proceed as follows:
1. Push the saw head to the rear and tighten the locking screw
of the pulling device (6).
2. Set the rotary table (8) to the 0° position and tighten the
fastening bolts for the rotary table (7). (see "Straight cuts").
3. Position the saw head in transport position (see "Transport").
4. Check the angle between saw blade and work piece stop
using a square (A, not supplied).
5. Loosen the set screws (2 on each side) for the work piece
stop (12) if the work piece stop needs to be adjusted
6. Align the work piece stop along the square and tighten the
locking screw again.
7. If the mitre angle indicator is not set to 0°, loosen the screw
and align the mitre angle indicator (26).
22
B
B
C