Preparing For Commissioning; Commissioning - ATIKA T 205 Notice Originale

Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
Protect yourself against an electric shock. Avoid touching
earthed parts with your body.
The connector of the connection cable must be splash-
proof.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Regularly check the saw cable and if damaged, have it
renewed by a recognised skilled electrician.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current
circuit breaker (30 mA).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts and accessorie parts.
Accidents can arise for the user through the use of other
spare parts. The manufacturer is not liable for any
damage or injury resulting from such action.

Preparing for commissioning

To achieve flawless functioning of the machine, please
follow the instructions listed:
Place the saw in a place that fulfils the following conditions:
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
To ensure secure footing, the saw must be bolted down on a
solid surface (e.g. workbench or similar) at optimal working
height:
− Make 3 holes in the support matching the holes in the
base plate.
All manuals and user guides at all-guides.com
Setting up the table extension
Mounting the length stop

Commissioning

Rotational direction of the saw blade
Selection of saw blades
or damaged saw bands are used and that the diameter of the
blade location hole is 16 mm.
Take care thet the selection of the saw blade is suitable for the
material to be cut.
The saw blade supplied as a standard is suitable for timber and
most plastics.
19
− Bolt the device down.
Before each use, check
− Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
− that the guard is in a proper condition
− the splitting wedge setting (see splitting wedge setting)
− the table insert for proper condition
− whether the pushstick is to hand
− the saw blade for flawless condition
Do not use any cracked saw blades or such that have
changed their shape.
Do not use any saw blades made of HSS steel.
Immediately replace a worn or damaged table insert.
When sawing, place yourself to the side of the danger area
(saw blade).
Lower the guard onto the bench top
− when working on the workpiece
− when interrupting the work or leaving the saw
The table extension can be hung either to the right or to
the left of the saw table.
1. Fold the support braces (17) of the table extension
down.
2. Hang the table extension on the saw table.
3. Turn the thumb screws (16) in or out to bring the
table flush with the saw table. Then tighten the
locking nuts.
1. First, you have to fix the clamping elements to the
length feed stop.
2. Do not fasten the star knob screws (20) yet!
3. Push the length stop on the table top. Be sure to to
push the guide plates over the edge of the table top.
4. Secure the stop ruler (2) together with parts 21 and
two screws to the length stop.
5. Push the length stop to the desired position and fix it
with parts 20.
Ensure that the rotational direction of the saw blade is the
same as the rotational direction given on the guard (10).
Consider when selecting the saw blade, that no edgeless
1 - 2
3 - 7