Adjusting The Saw - ATIKA KGSZ 250 N Notice Originale

Vice assembly
Always secure work pieces to be handled. Do not cut
work pieces that cannot be secured with the vice
assembly.
The vice assembly can be positioned to the left or right of
the saw head.
• Insert the vice assembly (20) at the right or left into the hole
provided.
• Secure it with the wing screws (21).
• Press the work piece firmly against the work piece stop (11).
• To fix the work piece turn the machine knob (22) of the work
piece clamping device clockwisely.

Adjusting the saw

Before setting operations:
− switch off device
− wait for standstill of the saw blade
− pull out power plug
Setting the work piece stop
To adjust a work piece stop that has shifted during
transport, proceed as follows:
1. If required, adjust the saw head vertically and tighten the
incline angle locking knob (25).
2. Push the saw head to the rear and tighten the locking screw
of the pulling device (6).
3. Loosen the locking screw (7) for the rotary table (8), press
the locking lever (7A) and swivel the saw head to the 0°
position.
4. Press the saw head down (transport position) and
secure it using the transport locking pin (5).
5. Check the angle between saw blade (36) and work piece
stop (11) using a square (A, not supplied).
6. Loosen the set screws (12) for the work piece stop if the
work piece stop needs to be adjusted.
7. Align the work piece stop along the square and tighten the
locking screw again.
8. If the mitre angle indicator (27) is not set to 0°, loosen the
screw and align the mitre angle indicator.
Adjusting the incline of the saw head
Also check the angle of the saw head to the rotary table.
Checking the 90° angle:
1. If required, adjust the saw head vertically and tighten the
incline angle locking knob (25).
2. Push the saw head to the rear and tighten the locking screw
(6).
3. Loosen the locking screw (7) for the rotary table (8), press
the locking lever (7A) and swivel the saw head to the 0°
position.
All manuals and user guides at all-guides.com
4.
• Loosen the locking nut (29) for the set screw (28).
• Loosen the incline angle locking knob (25).
• Adjust the set screw (28) by turning it clockwisely or
• Retighten the locking nut (29) for the set screw (28).
• If necessary, loosen the screw for the indicator (27) and shift
Checking the 45° angle:
using a protractor (B, not supplied).
Proceed as follows if the angle is not exactly 45°:
• Loosen the locking nut (31) for the set screw (30).
• Loosen the incline angle locking knob (25).
• Adjust the set screw (30) by turning it clockwisely or
• Retighten the locking nut (31) for the set screw (28).
• If necessary, loosen the screw for the indicator (27) and shift
Adjusting the saw blade depth
1. Adjust the saw head vertically and tighten the incline angle
2. Push the saw head to the rear and tighten the locking screw
3. Loosen the locking screw (7) for the rotary table (8), press
4. Carefully turn the saw blade by hand to ensure that it turns
5. Press the saw head down (transport position) and secure it
6. The saw blade depth is correctly adjusted when the saw
7. To adjust the correct saw blade depth:
20
Check the angle using a square (A, not supplied).
Proceed as follows if the angle is not exactly 90°:
counterclockwisely so that the saw blade comes in contact
with the square (90°).
it until it points to "0". Tighten the screw again.
Put the saw head to the 45° position and check the angle
counterclockwisely so that the saw blade comes in contact
with the protractor ( 45°).
it until it points to "45". Tighten the screw again.
You must set the max. saw blade depth to ensure that
the saw blade does not touch the bottom of the saw
blade groove.
locking knob (25).
(6) of the pulling device.
the locking lever (7A) and swivel the saw head to the 0°
position.
freely.
using the transport locking pin (5).
blade is approx. 5 mm below the saw table.
Loosen the locking nut (33) for the set screw (32).
The saw head rises when you turn the set screw (32)
counterclockwisely.
The saw head lowers when you turn the set screw (32)
clockwisely.
Retighten the locking nut (33) for the set screw (32).