Description Of Device / Spare Parts; Assembling; Before The First Start-Up - ATIKA BWS 500-2 Notice Originale

Before switching on, check always that wrenches and adjusting tools
are removed.
Store unused equipment in a dry, locked place out of the reach of

children.
Adopt safe procedures for cleaning, maintenance and regular

removal of chips and dust to prevent the risk of fire.
Make sure during its entire foreseeable life cycle that the machine

including its parts cannot tip over or move in an uncontrolled manner
when transporting, assembling, putting out of service and scrapping
Electrical safety
 Design of the connection cable according to IEC 60 245 (H 07 RN-F)
with a core cross-section of at least
 1.5 mm² for cable lengths up to 25 m
 2.5 mm² for cable lengths over 25m
 Long and thin connection lines result in a potential drop. The motor
does not reach any longer its maximal power; the function of the
device is reduced.
 Plugs and coupler outlets on connection cables must be made of
rubber, plasticised PVC or other thermoplastic material of same
mechanical stability or be covered with this material.
 Protect yourself against an electric shock. Avoid touching earthed
parts with your body.
 The connector of the connection cable must be splash-proof.
 Wind off completely the cable when using a cable drum.
 Do not use the cable for purposes for which it is not meant. Protect
the cable against heat, oil and sharp edges. Do not use the cable to
pull the plug from the socket.
 Regularly check the saw cable and if damaged, have it renewed by a
recognised skilled electrician.
 When running the connection line observe that it does not interfere, is
not squeezed, bended and the plug connection does not get wet.
 Regularly check the extension cables and replace them if they are
damaged.
 Do not use any defective connection cables.
 When working outdoors, only use extension cables especially
approved and appropriately labelled for outdoor use.
 Do not set up any provisional electrical connections.
 Never bypass protective devices or deactivate them.
 Only hook up the machine by means of a fault-current circuit breaker
(30 mA).
The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or one of
our customer service points. Local regulations – especially
regarding protective measures – must be observed.
Repairs to other parts of the machine must be carried out by
the manufacturer or one of his customer service points.
Use only original spare parts. Accidents can arise for the user
through the use of other spare parts. The manufacturer is not liable
for any damage or injury resulting from such action.
14

Description of device / spare parts

Pos. Spare part-no. Description
1 365224 Safety flap
2 365248 Handle
3 Tilt table
4 365261 Support extension
4a 365264 Star grip screw M8x12
5 On/Off switch
6 365265 Safety hook
7 365268 Wheel
7a Washer Ø 20
7b 392211 Splint 2,5x32
8 365267 Axle
8a Screw M8x20
8b Washer Ø 8
8c Nut M8
9 365275 Locking pin
10 Motor
11 365223 Limit stop
12 365221 Cover plate
12a
Washer Ø 6
12b Nut M6
13 Safety guard
14 365260 Longitudinal stop
14a 365264 Star grip screw M6x20
15 365246 Recuperating bolt complete
15a Support pin
15b Spring cotter pin
15c Washer  20
15d Support pin
16 365218 Front saw blade flange
16a Washer  12
16b Screw M12x30
17 365216
Saw blade - TCT  505 mm
18 365217 Rear saw blade flange no pic.
19 365215
Plastic inset (Set)
19a Screw ST 4,2x12
20 365219
Feather key 8x7x30
21 365272 Fan hood.
22 365273 Fan blade no pic.
23 365213 Mounting tool
24 365256 Safety label

Assembling


Observe the enclosed mounting sheet!
Assembling the wheels
Mount the axle (8) to the device unit.
4x hexagon screw M8x20 (8a), 8x washer A8.4 (8b), 4x nut M8
(8c), self-locking
First slide 2 washers (7a) each onto the ends of the axle. Plug on
the wheels (7) and secure each of them on its side with a washer
(7a) and a cotter pin (7b). [2x cotter pin, 6x washer A 20].
Assembling the support extension
Loosen the star grip screw (4a). Insert the support extension (4) in
the tilt table and secure it using the star grip screw.