Fitting And Adjusting The Longitudinal Stop; Working Instructions; Working With The Saw; Cutting Narrow Workpieces - ATIKA T 250 Eco-3 Notice Originale

Fitting and adjusting the longitudinal stop

Fit the longitudinal stop to the saw table plate.
The longitudinal stop (13) can be installed on the left or right of
the saw blade. To attach the fence on the other side of the stop,
loosen the two thumb nuts (D)

remove the fence (13A)

 remove the two thumb nuts and pull out the screws
 insert the screws from the opposite side through the stop
and screw on the thumb nuts by some turns
 reinstall the fence
 tighten the thumb nuts
release the clamping lever (25) and pull the length

stop out of the guide groove
slide the length stop in the guide groove from the

opposite side and press the clamping lever (25) down for
clamping.
Make sure that the fences are correctly adjusted. (See "


Working instructions").

Setting the longitudinal stop
1. Place the longitudinal stop (13) in the guide profile (24) on
the bench.
2. Set the desired dimension and turn the lever (25) down.
3. To obtain a precise cut, first make a test cut and then
readjust the stop as needed.

Working with the saw

Before starting to work consider the following safety
advices to keep the risk of injuries as small as
possible.
 Protective guard, splitting wedge and saw blade ok?
 Place your hands flat on the workpiece with fingers closed.
 Stoppers (fences) ready for use and pushstick to hand?
 Workplace tidied?
 You may not start to operate the machine until you have
read these operating instructions, observed all the
instructions given and installed the machine as described!
Before making adjustments to the saw settings (e.g.
replacing the saw blade etc.)
 switch off device
 Wait for standstill of the saw blade
 pull out main plug
Also, note the following important points:
 Place yourself outside of the area of danger.
 Place your hands flat on the workpiece with fingers closed.
With it, lead the work piece with the hand only up to the
leading edge of the saw blade protection.
 Make sure the safety guard lowers itself onto the workpiece
on its own.
 Never remove loose splinters, chips, or similar by hand.
Observe all safety instructions in any case.
15

Cutting narrow workpieces

(Width less than 150 mm)
Push the workpiece forward with both hands, in the
area of the saw blade, use the pushstick (19).
When working on very flat and narrow workpieces
(Width 30 mm and less) use the lower guide are of
the fence (13A).
Use a push stick if the workpiece is narrower than
50 mm.
You can easily make your own push block / push stick. To
do so, screw the handle for the pushing block (not included with
the delivery, order no. 361700) onto a board of the right size.
The board should be 300 to 400 mm long, 80 to 100 mm wide
and 15 to 20 mm thick. The push block handle must be
replaced if damaged.

Cutting wide workpieces

 With the flat of the hand and the fingers closed, push the
work piece to be cut along the stop.

Cross cuts / mitre cuts

 Push the transverse stop (11) into one of the guide grooves
on the table and set the transverse stop to the required
angle.
 Place the workpiece to be cut against the stop rails.
 Hold the workpiece firmly in place and push it past the saw
blade using the transverse stop (11). Use the pushing bar
(19) if necessary.

Cutting lengthwise and tilted

Adjust the saw blade as described in "Adjusting the saw blade
tilt".
When the saw blade is tilted, always attach the stop to
the right side.

Maintenance and Care

Before each maintenance and cleaning
work
 switch off device
 wait for stop of chain saw
 pull out main plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or
companies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.