Disposal Of Packaging; Electrical Connection - LAVAZZA BLUE LB2300 Mode D'emploi

Installation of the machine - Service Provider Manual
- be used if damaged;
- be handled with damp or wet hands;
- be wound in a coil when the machine is in use.
- be tampered with.
• It is forbidden to:
- Install the machine other than as described in
Chapter 10, or outdoors.
- Install the machine in a location where water
jets may be used.
- Disable the security measures installed by the
manufacturer.
- Use the machine in proximity to fl ammable and/
or explosive materials.
- Leave plastic bags, polystyrene, nails, etc within
the reach of children, as they are potential ha-
zards.
- Allow children to play near the machine.
- Use replacement parts other than those recom-
mended by the manufacturer.
- Make any technical modifi cations to the machi-
ne.
- Immerse the machine in any kind of liquid.
- Wash the machine using a jet of water.
- Use the machine in any manner other than as
described in this manual.
- Install the machine on top of other appliances.
- Use the machine in explosive or harsh environ-
ments, or with high concentrations of dust or
oily substances suspended in the air;
- Use the machine in an environment where there
is a risk of fi re;
- Use the machine to dispense products other
than those it is designed for.
• Before cleaning the machine, ensure the plug is
disconnected from the power socket; do not wash
it with fuel and/or solvents of any kind.
• Do not place the machine near heating equipment
(such as stoves or radiators).
• In case of fi re, use carbon dioxide (CO
guishers. Do not use water or dry powder extin-
guishers.
10.2 Stop functions
The machine is stopped using the power button.
10.3 List of accessories supplied
Manual: Instructions for using the machine.
Water hardness test: quick test to determine the
hardness of the water used to prepare beverages; this
test is of fundamental importance, in order to set the
hardness of the water used by the machine.
Key for the water tank and the access door to the
service compartment: this prevents access to the wa-
ter tank and brew unit by unauthorised personnel.
• 34 •
All manuals and user guides at all-guides.com
Water network pipe (only for certain models with
water network): establishes the connection between
the machine and the drinking water network (see sec-
tion 10.7).
10.4 Assembly-Siting
The machine must not be installed outdoors
or in environments in which jets of water or
steam are used.
The presence of magnetic fi elds or proxi-
mity to electrical machines which generate
disturbances could cause the electronic controls of
the machine to malfunction.
Important.
At temperatures close to 0°C, internal parts
containing water are at risk of freezing. Do not use
the machine under these conditions.
To ensure correct and effi cient performance of the ap-
pliance, comply with the following recommendations:
• maximum humidity: 90%.
• the site should be suitably prepared for the installa-
tion of the machine;
• the surface on which the machine is installed should
be level, solid and stable, with a gradient no greater
than 2°;
• the location should be adequately lit, ventilated and
clean, and the power socket should be easily ac-
) extin-
2 cessible.
Access to the machine and the plug should
be kept clear at all times, in order to allow
users to easily reach them and to leave the area
immediately if required.
The following illustration shows the required access
distances:
• to the keypad on the front of the appliance
• to the service units in the event of malfunction.
400
100
200
After placing the packing container near the installation
site, proceed as follows:
• ensure that the container has not been tampered
with during transport and that the original packaging
is intact and closed;
• open the container;
• check the condition and model of the machine;
• check the contents of the accessories bag enclo-
sed with the machine (see "10.3 List of accessories
supplied");
• remove the machine from its original packaging;
• remove any remaining packaging from the machi-
ne;
• lift the machine and place it in the designated
area.
10.5

Disposal of packaging

After the packing container is opened, it is recommen-
ded that the packaging materials are separated accor-
ding to type and disposed of in accordance with the
regulations in force in the country of use.
We recommend keeping the container for
future transfers or transportation.
10.6

Electrical connection

This operation should only be performed
by specialist technical personnel or by the
service provider.
The machine is designed to work with single-phase vol-
tage matching the rating on the identifi cation plate (1.4
Machine identifi cation).
Before plugging in the machine, make sure that the
power button is switched to "0".
The Service Provider makes and is responsible for the
electrical connection of the machine.
The machine should be connected to the mains using
the plug installed on the power cord, in accordance
with:
• Laws and Regulations in force in the place and at
the time of installation;
• The information shown on the technical specifi ca-
tions plate on the side of the machine.
Warning: the electric socket which the ap-
pliance is connected to must be easily ac-
cessible by the user, in order to allow it to be easily
disconnected from the mains when necessary.
It is forbidden to:
• Use extensions of any kind.
• Replace the original plug.
• Use adaptors.
sizes in millimeter
10.7 Water connection (only for models
with water network)
This connection is only required for machi-
nes fi tted with a water network connector.
This operation should only be performed
200 by specialist technical personnel or by the
service provider.
200
The machine is designed for use with the drinking wa-
ter network.
Before connecting the supply pipe to the
water network, allow the water to run until
it is clear.
The distance between the supply for the
electrical connection and the water connec-
tion should respect the regulations in force at the
time of installation.