Nice Riva Serie Instructions Et Avertissements Pour L'installation page 45

1 1 GENERAL WARNINGS
a
WARNING! Important safety instructions Observe all
the instructions as improper installation may cause se-
rious damages
a
WARNING! Important safety instructions It is impor-
tant to comply with these instructions to ensure per-
sonal safety Store these instructions carefully
WARNING! Please abide by the following warnings:
– Before commencing the installation, check the "Product
technical specifications", in particular whether this product
is suitable for automating your guided part. Should it not be
suitable, do NOT proceed with the installation.
– The product cannot be used before it has been commis-
sioned as specified in the "Testing and commissioning"
chapter.
a
According to the latest European legislation, an au-
tomated device must be constructed in conformity to
the harmonised rules specified in the current Machin-
ery Directive, which allow for declaring the presumed
conformity of the automation Consequently, all the
operations for connecting the product to the mains
electricity, its commissioning and maintenance must
be carried out exclusively by a qualified and expert
technician
– Before proceeding with the product's installation, check that
all the materials are in good working order and suited to the
intended applications.
– The product is not intended for use by persons (including
children) with reduced physical, sensory or mental capaci-
ties, nor by anyone lacking sufficient experience or familiarity
with the product.
– Children must not play with the appliance.
– Do not allow children to play with the product's control devic-
es. Keep the remote controls out of reach of children.
a
In order to avoid any danger from inadvertent reset-
ting of the thermal cut-off device, this appliance must
not be powered through an external switching device,
such as a timer, or connected to a supply that is regu-
larly powered or switched off by the circuit
– The system's power supply network must include a discon-
nection device (not supplied) with a contact opening gap
permitting complete disconnection under the conditions en-
visaged by Overvoltage Category III.
– Handle the product with care during installation, taking care
to avoid crushing, denting or dropping it, or allowing contact
with liquids of any kind. Keep the product away from sources
of heat and naked flames. Failure to observe the above can
damage the product, and increase the risk of danger or mal-
function. Should this happen, stop installation immediately
and contact Customer Service.
1 - GENERAL SAFETY WARNINGS AND PRECAUTIONS
– The manufacturer declines all liability for damages to proper-
ty, objects or people resulting from failure to observe the as-
sembly instructions. In such cases, the warranty for material
defects shall not apply.
– The weighted sound pressure level of the emission A is lower
than 70 dB(A).
– Cleaning and maintenance reserved for the user must not be
carried out by unsupervised children.
– Before intervening on the system (maintenance, cleaning),
always disconnect the product from the mains power supply
and from any batteries.
– Inspect the system frequently, in particular the cables, springs
and supports to detect any imbalances and signs of wear or
damage. Do not use the product if it needs to be repaired or
adjusted, because defective installation or incorrect balanc-
ing of the automation can lead to injuries.
– The packing materials of the product must be disposed of in
compliance with local regulations.
– Keep persons away from the gate when it is manoeuvred
using the control elements.
– When operating the gate, keep an eye on the automated
mechanism and keep all bystanders at a safe distance until
the movement has been completed.
– Do not operate the product if anyone is working nearby; dis-
connect its power supply before permitting such work to be
done.
– If the power cable is damaged, it must be replaced by the
manufacturer or by an appointed servicing company or simi-
larly qualified person in order to prevent any form of risk.
– Warning! Transport the product using the relevant hand trol-
ley and the handles on the package to ensure that the oper-
ations are conducted safely.
1 2 INSTALLATION WARNINGS
– Prior to installing the drive motor, check that the door is in
good working order, correctly balanced and that it opens and
closes properly.
– Before installing the drive motor, remove all unnecessary
ropes or chains and deactivate any equipment not required
for motorised operation, such as locking devices.
– If the gate to be automated is fitted with a pedestrian door,
the system must be equipped with a control system that in-
hibits motor operation when the pedestrian door is open
– Install the manoeuvre device for manual unlocking at less
than 1.8 m above the ground. NOTE - If removable, the ma-
noeuvre device must be kept next to the door when removed.
– Make sure that the control elements are kept far from moving
parts but nonetheless directly within sight. Unless a selector
is used, the control elements must be installed at least 1.5 m
above the ground and must not be accessible.
ENGLISH – 3