Setting Date/Time; Language Setting; Customer Service - Nordcap MORETTI T75G Mode D'emploi

minute set cooking time, for a total cooking time of 24 minutes. This
setting is not provided for standard operations.
NOTE:
When using the special STEP and RETURN
programs, after 2 minutes from the last bake, if no key is selected,
the oven automatically enters the ECO STAND-BY mode.
Once a new bake or a different cooking program is selected, the
oven returns to the standard setting mode.
3.6.11 CONVEYOR BELTSETTING
(only for T75G-TT98G)
Press MENU and select "Conveyor Belt" to access the conveyor belt
settings. There are two functions:
- "Conveyor Belt Lock" it stops the conveyor belt while the gas
power and cooking parameters supplied is intact. Press OK to
enable . The conveyor belt stops and the icon status of the
conveyor belt is displayed in orange (enabled ).
NOTE:
The conveyor belt lock can be enabled also by
setting the "Cooking time" parameter to 00:00.
- "Start / Stop" is enabled by default; this function allows the
conveyor belt to start only when the set temperature is reached
after a sequence of beeps. This ensures the conveyor belt
components wear less, and a lower heat exchange between the
cooking and the outside chamber during the heating and cooling
process.
In both cases a check mark (√) to the right of the menu item, indicates
if the function is enabled.
3.6.12 "LOCK/UNLOCK"
This function can be used to block certain operations, for safety
purposes.
The following functions are disabled:
-Storage/modifying and deleting programs
-Changing cooking parameters
The following functions are still enabled:
-Use of programs
-Select "Eco standby", "Step", " "Conveyor Belt Lock
NOTE:
when LOCK is enabled, all unauthorised operations
are displayed on the main screen by the intermittent LOCK icon.
•
ACTIVATION/DEACTIVATION
T75G-TT98G
To enable the "Lock" access MENU , select "Lock/Unlock" and press
OK. Select "Lock" and press OK. The display requires a four digit
secret password. To enter pass word use the up/down arrow keys to
select the desired number and press OK. When the control unit is
delivered, 1 1 1 1 is set as password. If the password entered is
correct, a message to confirm unblocked status is displayed and
redirected automatically to the main screen where the LOCK status
icon displays a closed padlock. If a wrong password is entered, a
message will inform the user to re-enter the password.
To disable the "Lock" access menu, select "Lock/Unlock" and press
OK. Select "Unlock" and press OK. Enter the password with the same
procedure described for the lock operation.
T64G
In order to enable or disable the "Lock" function, press the relative
button simultaneously with the "Up Arrow" key (fig. 31b item 20+12).
The message "LOC" will be shown on the display on this occasion and
each time the safe and protected operation is enabled. To disable,
simultaneously press the "Lock" and "Down Arrow" keys (fig. 31b
item 20+13). The display (fig. 31b item D).shows the message "-LOC"
•
EDIT PASSWORD
(only for T75G-TT98G)
To enter a new secret code access MENU, select "Edit password" and
press OK. The display now requires the current password to be
entered, followed by the new password and confirms the new
password. To enter pass word use the up/down arrow keys to select
the desired number and press OK.
3.6.13 DISPLAY (TT98G only)
Default display and only one temperature setting set point as shown in
Fig. 30a. The TT98G model has two burners by default; the display
mode at two temperatures can be enabled. This operation mode
differentiates between the oven's left zone set-point temperatures and
the right zone.
To enable this mode to use the oven enter MENU, select "Display" and
press OK. Use the up/down arrow keys to select "2 temperatures" and
press OK. The main screen will change as shown in Fig. 30 c. Set the
two temperatures with the keys "+" and "-" to edit the operating
temperature of the left area; use the "+" and "-" down keys to edit the
operating temperature of the right area.
All features of the oven in "2 temperatures mode" are enabled and valid
according to the instructions in this manual.
NOTE:
The display may change even when the oven is on.
When moving from one mode to another, ensure the set-point
temperatures are correct and reset if necessary.
NOTE:
Refer to fig. 3.6.7 for the cooking program
management, but if "2 temperatures" is stored the left temperature
can be distinguished from the right.
To return to standard one temperature display, re-access the "Display"
menu, select "1 temperature"and press Ok.

3.6.14 SETTING DATE/TIME

(only for T75G -TT98G)
To set the time and date, press MENU, use the up/down arrow keys to
select the "Date/Time" and press OK. Use the up/down arrow keys
to move in the edit field. Use the "+" e "-" keys to increase/decrease
the selected field. Press OK to confirm editing. Press RETURN to
return to the previous screen without confirming the changes.
The time representation format is HH: MM. The date representation
format is DD/MM/YY.

3.6.15 LANGUAGE SETTING

(only for T75G-TT98G)
To set language, press MENU, with the up/down arrow keys, select
"Language" and press OK. Use the up/down arrow keys to scroll
through the list until the desired language and press OK.
RETURN to return to the previous screen without confirming the
changes.
3.6.16 ° C/° F SETTING
The oven sets/displays the temperatures in degrees Centigrade (° C) or
degrees Fahrenheit (° F) by default.
T75G-TT98G
The current setting is displayed on the main screen to the right of the
temperature with the appropriate symbol.
To edit current setting, press MENU, with the up/down arrow keys,
select "Language" and press OK. Scroll through the list with the
up/down arrows until the desired item and press OK. Press RETURN to
return to the previous screen without confirming the changes.
T64G:
Access the general settings by simultaneously pressing "Lock" +
"P/hotkey" (fig. 31b item 20+18). Use the "Right arrow" or "Left
Arrow" (fig. 31b item 14 and 15) to select the parameter "SCLT" in
the display (fig. 31b item D). Use the "Up Arrow" / "Down Arrow"
keys (fig. 31b item 14 and 15) to select the "cooking time display" (fig.
31b item C):
- dEGC for centigrade
- dEGF for Fahrenheit
Press OK to exit and save the settings.

3.6.17 CUSTOMER SERVICE

(only for T75G-TT98G)
This menu lists the operations required during Customer service.
To access, press MENU, with the up/down arrow keys, select
"Customer Service" and press OK.
Scroll the up/down arrow keys on the display to select the items:
- "Info": displays information about Service, software version
installed and current oven configuration. This screen is useful to
request customer service.
WARNING!
manufacturer are allowed to perform the following procedures,
otherwise the oven may not function properly.
- "Update software": starts software update procedure;
- "Reset": start parameters reset procedure (any current programs
will be saved)
- "Factory Default": start default general procedure
WARNING!
deleted; run the "EXPORT USB" procedure described in 3.6.7 if
programs must be saved before the Default procedure. After
completing the Default procedure, programs saved can be
reinstalled with the "IMPORT USB" procedure described in 3.6.7
UK/11
Only qualified staff authorised by the
Any Programs stored in the memory will be
Press